S9S08SG16E1VTJ Freescale Semiconductor, S9S08SG16E1VTJ Datasheet - Page 60

• Manufacturer Part Number: S9S08SG16E1VTJ
• Description: MCU 16K FLASH 20-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of S9S08SG16E1VTJ

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 20-TSSOP
• Processor Series: S08SG
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SPI, SCI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 2
• Operating Supply Voltage: - 0.3 V to + 5.8 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08SG32, DEMO9S08SG32AUTO, DEMO9S08SG8, DEMO9S08SG8AUTO
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• On-chip Dac: 10 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Chapter 4 Memory
4.7.6
Only five command codes are recognized in normal user modes as shown in
4.5.3, “Program and Erase Command
erase operations.
All other command codes are illegal and generate an access error.
It is not necessary to perform a blank check command after a mass erase operation. Only blank check is
required as part of the security unlocking mechanism.
60
FACCERR
FBLANK
Reset
Field
4
2
W
R
FLASH Command Register (FCMD)
Access Error Flag — FACCERR is set automatically when the proper command sequence is not obeyed exactly
(the erroneous command is ignored), if a program or erase operation is attempted before the FCDIV register has
been initialized, or if the MCU enters stop while a command was in progress. For a more detailed discussion of
the exact actions that are considered access errors, see
writing a 1 to FACCERR. Writing a 0 to FACCERR has no meaning or effect.
0 No access error.
1 An access error has occurred.
FLASH Verified as All Blank (erased) Flag — FBLANK is set automatically at the conclusion of a blank check
command if the entire FLASH array was verified to be erased. FBLANK is cleared by clearing FCBEF to write a
new valid command. Writing to FBLANK has no meaning or effect.
0 After a blank check command is completed and FCCF = 1, FBLANK = 0 indicates the FLASH array is not
1 After a blank check command is completed and FCCF = 1, FBLANK = 1 indicates the FLASH array is
0
0
7
completely erased.
completely erased (all 0xFF).
Page erase (512 bytes/page)
Byte program — burst mode
Table 4-12. FSTAT Register Field Descriptions (continued)
Mass erase (all FLASH)
0
0
6
Figure 4-10. FLASH Command Register (FCMD)
Byte program
Blank check
Command
Table 4-13. FLASH Commands
0
0
Execution,” for a detailed discussion of FLASH programming and
5
MC9S08SG32 Data Sheet, Rev. 8
0
0
4
FCMD
Description
0x05
0x20
0x25
0x40
0x41
FCMD
Section 4.5.5, “Access
3
0
0
Equate File Label
mPageErase
mMassErase
mBurstProg
mByteProg
mBlank
0
0
2
Table
Errors.” FACCERR is cleared by
4-13. Refer to
Freescale Semiconductor
0
0
1
Section
0
0
0