MC9S08QG84CFFER Freescale Semiconductor, MC9S08QG84CFFER Datasheet - Page 59

• Manufacturer Part Number: MC9S08QG84CFFER
• Description: IC MCU 8BIT 8K FLASH 16-QFN
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QG84CFFER

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 12
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-QFN
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 20 MHz
• Data Ram Size: 512 B
• On-chip Adc: Yes
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Mounting Style: SMD/SMT
• Height: 1 mm
• Interface Type: I2C, SCI, SPI
• Length: 5 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 1.8 V
• Width: 5 mm
• For Use With: DEMO9S08QG8E - BOARD DEMO FOR MC9S08QG8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

4.7.5
Freescale Semiconductor
Reset
FPVIOL
FCBEF
FPDIS
FCCF
Field
Field
FPS
7:1
0
7
6
5
W
R
FCBEF
FLASH Status Register (FSTAT)
FLASH Protect Select Bits — When FPDIS = 0, this 7-bit field determines the ending address of unprotected
FLASH locations at the high address end of the FLASH. Protected FLASH locations cannot be erased or
programmed.
FLASH Protection Disable
0 FLASH block specified by FPS7:FPS1 is block protected (program or erase not allowed).
1 No FLASH block is protected.
FLASH Command Buffer Empty Flag — The FCBEF bit is used to launch commands. It also indicates that the
command buffer is empty so that a new command sequence can be executed when performing burst
programming. The FCBEF bit is cleared by writing a 1 to it or when a burst program command is transferred to
the array for programming. Only burst program commands can be buffered.
0 Command buffer is full (not ready for additional commands).
1 A new burst program command can be written to the command buffer.
FLASH Command Complete Flag — FCCF is set automatically when the command buffer is empty and no
command is being processed. FCCF is cleared automatically when a new command is started (by writing 1 to
FCBEF to register a command). Writing to FCCF has no meaning or effect.
0 Command in progress
1 All commands complete
Protection Violation Flag — FPVIOL is set automatically when FCBEF is cleared to register a command that
attempts to erase or program a location in a protected block (the erroneous command is ignored). FPVIOL is
cleared by writing a 1 to FPVIOL.
0 No protection violation.
1 An attempt was made to erase or program a protected location.
1
7
= Unimplemented or Reserved
FCCF
1
6
Table 4-11. FPROT Register Field Descriptions
Table 4-12. FSTAT Register Field Descriptions
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 5
Figure 4-9. FLASH Status Register (FSTAT)
FPVIOL
0
5
FACCERR
0
4
Description
Description
3
0
0
Chapter 4 Memory Map and Register Definition
FBLANK
0
2
0
0
1
0
0
0
57