STM32F103ZCT6 STMicroelectronics, STM32F103ZCT6 Datasheet - Page 86

• Manufacturer Part Number: STM32F103ZCT6
• Description: MCU ARM 32BIT 256K FLASH 144LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103ZCT6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 112
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 21x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Controller Family/series: (ARM Cortex) STM32
• No. Of I/o's: 112
• Ram Memory Size: 32KB
• Cpu Speed: 72MHz
• No. Of Timers: 8
• Featured Product: STM32 Cortex-M3 Companion Products
• Eeprom Size: -
• Cpu Family: STM32
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 72MHz
• Interface Type: CAN/I2C/SPI/USART
• Total Internal Ram Size: 48KB
• # I/os (max): 112
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2V
• On-chip Adc: 3(21-chx12-bit)
• On-chip Dac: 2(2-chx12-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Electrical characteristics
5.3.14
Table 46.
1. FT = Five-volt tolerant. In order to sustain a voltage higher than V
2. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization, not tested in production.
3. With a minimum of 100 mV.
4. Leakage could be higher than max. if negative current is injected on adjacent pins.
5. Pull-up and pull-down resistors are designed with a true resistance in series with a switchable PMOS/NMOS. This
86/130
Symbol
V
R
R
C
V
V
I
disabled.
MOS/NMOS contribution
lkg
hys
PU
PD
IH
IO
IL
Standard IO input low
level voltage
IO FT
voltage
Standard IO input high
level voltage
IO FT
voltage
Standard IO Schmitt
trigger voltage
hysteresis
IO FT Schmitt trigger
voltage hysteresis
Input leakage current
Weak pull-up equivalent
resistor
Weak pull-down
equivalent resistor
I/O pin capacitance
I/O port characteristics
General input/output characteristics
Unless otherwise specified, the parameters given in
performed under the conditions summarized in
compliant.
I/O static characteristics
All I/Os are CMOS and TTL compliant (no software configuration required). Their
characteristics cover more than the strict CMOS-technology or TTL parameters. The
coverage of these requirements is shown in
in
(1)
(1)
Figure 44
Parameter
(5)
input low level
input high level
(2)
to the series resistance is minimum
and
(2)
(5)
(4)
Figure 45
V
V
V
V
Standard I/Os
DD
DD
SS
IN
Conditions
V
V
= 5 V,
> 2 V
≤
≤
IN
IN
2 V
V
for 5 V tolerant I/Os.
=
=
IN
V
V
I/O FT
≤
SS
DD
Doc ID 14611 Rev 8
V
DD
(~10% order)
0.41*(V
0.42*(V
5% V
DD
STM32F103xC, STM32F103xD, STM32F103xE
DD
Figure 42
+0.3 the internal pull-up/pull-down resistors must be
DD
–0.3
–0.3
Min
200
30
30
-2 V)+1.3 V
.
-2 V)+1 V
Table
DD
(3)
Table 46
10. All I/Os are CMOS and TTL
and
Typ
Figure 43
40
40
5
are derived from tests
0.32*(V
0.28*(V
for standard I/Os, and
V
DD
DD
DD
Max
5.5
5.2
-2 V)+0.75 V
±1
50
50
-2 V)+0.8 V
3
+0.3
Unit
mV
mV
kΩ
kΩ
µA
pF
V
V
V
V