STM32F103ZCT6 STMicroelectronics, STM32F103ZCT6 Datasheet - Page 41

• Manufacturer Part Number: STM32F103ZCT6
• Description: MCU ARM 32BIT 256K FLASH 144LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103ZCT6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 112
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 21x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Controller Family/series: (ARM Cortex) STM32
• No. Of I/o's: 112
• Ram Memory Size: 32KB
• Cpu Speed: 72MHz
• No. Of Timers: 8
• Featured Product: STM32 Cortex-M3 Companion Products
• Eeprom Size: -
• Cpu Family: STM32
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 72MHz
• Interface Type: CAN/I2C/SPI/USART
• Total Internal Ram Size: 48KB
• # I/os (max): 112
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2V
• On-chip Adc: 3(21-chx12-bit)
• On-chip Dac: 2(2-chx12-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

STM32F103xC, STM32F103xD, STM32F103xE
5.2
Absolute maximum ratings
Stresses above the absolute maximum ratings listed in
Table 8: Current
damage to the device. These are stress ratings only and functional operation of the device
at these conditions is not implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
Table 7.
1. All main power (V
2. V
Table 8.
1. All main power (V
2. Negative injection disturbs the analog performance of the device. See note 3 below
3. Positive injection is not possible on these I/Os. A negative injection is induced by V
4.
5. When several inputs are submitted to a current injection, the maximum ΣI
|V
V
V
supply, in the permitted range.
allowed injected current values.
supply, in the permitted range.
never be exceeded. Refer to
values.
never be exceeded. Refer to
values.
positive and negative injected currents (instantaneous values).
Symbol
SSX
I
A positive injection is induced by V
|ΔV
ESD(HBM)
ΣI
DD
INJ(PIN)
IN
Symbol
V
INJ(PIN)
IN
I
I
maximum must always be respected. Refer to
–V
VDD
DDx
VSS
I
− V
IO
(2)
SS
|
SS
(2)
|
Voltage characteristics
Current characteristics
External main supply voltage (including V
and V
Input voltage on five volt tolerant pin
Input voltage on any other pin
Variations between different V
Variations between all the different ground pins
Electrostatic discharge voltage (human body
model)
characteristics, and
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Injected current on five volt tolerant pins
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
DD
DD
, V
, V
DD
DDA
DDA
)
(1)
) and ground (V
) and ground (V
Table 7: Voltage characteristics
Table 7: Voltage characteristics
Doc ID 14611 Rev 8
IN
Ratings
>V
DD
DD
SS
/V
Table 9: Thermal characteristics
SS
SS
while a negative injection is induced by V
DDA
ground lines (sink)
, V
, V
Ratings
SSA
SSA
power lines (source)
DD
Table 8: Current characteristics
) pins must always be connected to the external power
) pins must always be connected to the external power
power pins
(4)
DDA
for the maximum allowed input voltage
for the maximum allowed input voltage
(3)
(1)
Table 7: Voltage
see
Absolute maximum ratings
(electrical sensitivity)
(1)
V
V
INJ(PIN)
SS
SS
Section 5.3.12:
–0.3
Min
(5)
Electrical characteristics
− 0.3
− 0.3
is the absolute sum of the
may cause permanent
for the maximum
IN
Table 62 on page
IN
<V
characteristics,
<V
SS
V
SS
-5/+0
. I
Max.
− 25
± 25
DD
150
150
± 5
25
. I
Max
INJ(PIN)
4.0
4.0
50
50
INJ(PIN)
+ 4.0
must
must
105.
Unit
41/130
mA
Unit
mV
V