DSPIC30F2020-30I/MM Microchip Technology, DSPIC30F2020-30I/MM Datasheet - Page 2
![IC DSPIC MCU/DSP 12K 28QFN](/photos/6/81/68120/150-28-qfn_sml.jpg)
DSPIC30F2020-30I/MM
Manufacturer Part Number
DSPIC30F2020-30I/MM
Description
IC DSPIC MCU/DSP 12K 28QFN
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.AC164335.pdf
(286 pages)
2.DM300023.pdf
(22 pages)
3.DM300023.pdf
(18 pages)
4.DSPIC30F2011-20ISO.pdf
(66 pages)
5.DSPIC30F2011-20IP.pdf
(26 pages)
6.DSPIC30F1010-30ISO.pdf
(26 pages)
7.DSPIC30F1010-30ISO.pdf
(50 pages)
Specifications of DSPIC30F2020-30I/MM
Core Processor
dsPIC
Core Size
16-Bit
Speed
30 MIPs
Connectivity
I²C, IrDA, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
21
Program Memory Size
12KB (4K x 24)
Program Memory Type
FLASH
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-QFN
Core Frequency
15MHz
Core Supply Voltage
3.3V
Embedded Interface Type
I2C, SPI, UART
No. Of I/o's
21
Flash Memory Size
12KB
Supply Voltage Range
3V To 3.6V
Package
28QFN-S EP
Device Core
dsPIC
Family Name
dsPIC30
Maximum Speed
30 MHz
Operating Supply Voltage
3.3|5 V
Data Bus Width
16 Bit
Number Of Programmable I/os
21
Interface Type
I2C/SPI/UART
On-chip Adc
8-chx10-bit
Number Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
DM300023 - KIT DEMO DSPICDEM SMPS BUCKAC164322 - MODULE SOCKET MPLAB PM3 28/44QFNDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F2020-30I/MMB32
Manufacturer:
Microchip Technology
Quantity:
135
dsPIC30F Family Reference Manual
35.1
Figure 35-1:
DS70272B-page 35-2
SDO1
SCK1
SDI1
SS1
Introduction
Read SPI1BUF
SPI1 Module Block Diagram
Control
Sync
Transfer
The Serial Peripheral Interface (SPI) module is a synchronous serial interface useful for
communicating with other peripheral or microcontroller devices. These peripheral devices may
be serial EEPROMs, shift registers, display drivers, A/D converters, etc. The SPI module is
compatible with Motorola’s SPI and SIOP interfaces.
Each device in the dsPIC30F SMPS and Digital Power Conversion device family offers one SPI
module, designated SPI1.
The SPI1 serial interface consists of four pins:
• SDI1: Serial Data Input
• SDO1: Serial Data Output
• SCK1: Shift Clock Input or Output
• SS1: Active-Low Slave Select or Frame Synchronization I/O Pulse
The SPI1 module can be configured to operate using 2, 3 or 4 pins. In the 3-pin mode, SS1 is
not used. In the 2-pin mode, SDO1 and SS1 are both unused.
A block diagram of the SPI1 module is shown in Figure 35-1.
Note:
SPI1RXB
bit 0
Some devices in the dsPIC30F SMPS and Digital Power Conversion device family
do not contain the SS1 pin and, therefore, do not include the Framed SPI and Slave
Select functions. Refer to the specific device data sheet for details about available
SPI pins.
SPI1BUF
SPI1SR
Control
Clock
Shift Control
SPI1TXB
Transfer
Write SPI1BUF
Select
Edge
16
Secondary
1:1 to 1:8
Prescaler
Internal Data Bus
1:1/4/16/64
Prescaler
Primary
© 2008 Microchip Technology Inc.
F
SPI1CON1<1:0>
SPI1CON1<4:2>
Enable
Master Clock
CY