DSPIC30F2020-30I/MM Microchip Technology, DSPIC30F2020-30I/MM Datasheet - Page 15
![IC DSPIC MCU/DSP 12K 28QFN](/photos/6/81/68120/150-28-qfn_sml.jpg)
DSPIC30F2020-30I/MM
Manufacturer Part Number
DSPIC30F2020-30I/MM
Description
IC DSPIC MCU/DSP 12K 28QFN
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.AC164335.pdf
(286 pages)
2.DM300023.pdf
(22 pages)
3.DM300023.pdf
(18 pages)
4.DSPIC30F2011-20ISO.pdf
(66 pages)
5.DSPIC30F2011-20IP.pdf
(26 pages)
6.DSPIC30F1010-30ISO.pdf
(26 pages)
7.DSPIC30F1010-30ISO.pdf
(50 pages)
Specifications of DSPIC30F2020-30I/MM
Core Processor
dsPIC
Core Size
16-Bit
Speed
30 MIPs
Connectivity
I²C, IrDA, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
21
Program Memory Size
12KB (4K x 24)
Program Memory Type
FLASH
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-QFN
Core Frequency
15MHz
Core Supply Voltage
3.3V
Embedded Interface Type
I2C, SPI, UART
No. Of I/o's
21
Flash Memory Size
12KB
Supply Voltage Range
3V To 3.6V
Package
28QFN-S EP
Device Core
dsPIC
Family Name
dsPIC30
Maximum Speed
30 MHz
Operating Supply Voltage
3.3|5 V
Data Bus Width
16 Bit
Number Of Programmable I/os
21
Interface Type
I2C/SPI/UART
On-chip Adc
8-chx10-bit
Number Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
DM300023 - KIT DEMO DSPICDEM SMPS BUCKAC164322 - MODULE SOCKET MPLAB PM3 28/44QFNDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F2020-30I/MMB32
Manufacturer:
Microchip Technology
Quantity:
135
Figure 35-6:
35.3.3
© 2008 Microchip Technology Inc.
SS1
SCK Input
(CKP = 0
CKE = 1)
SCK Input
(CKP = 1
CKE = 1)
SDO
Output
SDI Input
(SMP = 0)
Input
Sample
(SMP = 0)
SPI1IF
SPITBF
SPIRBF
Note 1: Operation for 8-bit mode is shown; the 16-bit mode is similar.
(2,3)
Write to
SPI1BUF
2: The SS1 pin must be used for Slave mode operation when CKE = 1.
3: When the SSEN (SPI1CON1<7>) bit is set to ‘1’, the SS1 pin must be driven low to enable transmission and
4: Transmit data is held in SPI1TXB and SPITBF remains set until all bits are transmitted.
(4)
Framed SPI Modes
reception in Slave mode.
SPI1 Slave Mode Timing (CKE = 1)
Section 35. Serial Peripheral Interface (SPI) (Part II)
The SPI1 module supports a basic framed SPI protocol while operating in either Master or Slave
modes. The module uses four control bits to configure framed SPI operation:
• FRMEN (SPI1CON2<15>) enables the Framed SPI modes and causes the SS1 pin to be
• SPIFSD (SPI1CON2<14>) determines whether the SS1 pin is an input or an output (i.e.,
• FRMPOL (SPI1CON2<13>) selects the polarity of the frame synchronization pulse
• FRMDLY (SPI1CON2<1>) selects whether the synchronization pulse coincides with or
used as a frame synchronization pulse input or output pin. The state of SSEN
(SPI1CON1<7>) is ignored.
whether the module receives or generates the frame synchronization pulse).
(active-high or active-low) for a single SPI data frame.
precedes the first serial clock pulse.
bit 7
bit 7
bit 6
bit 5
(1)
bit 4
bit 3
bit 2
SPI1SR to
SPI1RXB
bit 1
bit 0
bit 0
DS70272B-page 35-15
35