ATTINY28L-4AU Atmel, ATTINY28L-4AU Datasheet - Page 30

• Manufacturer Part Number: ATTINY28L-4AU
• Description: IC MCU AVR 2K FLASH 4MHZ 32-TQFP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY28L-4AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 4MHz
• Peripherals: POR, WDT
• Number Of I /o: 11
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFP, 32-VQFP
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 32 B
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 11
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Package: 32TQFP
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 4 MHz
• Ram Size: 32 Byte
• Operating Supply Voltage: 3.3|5 V
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIPATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Ram Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

Port D
Port D as General Digital I/O
30
ATtiny28L/V
Figure 26. PORT B Schematic Diagram (Pins PB7 - PB5)
Port D is an 8-bit bi-directional I/O port with internal pull-up resistors.
Three I/O memory address locations are allocated for Port D, one each for the Data
Register – PORTD, $12, Data Direction Register – DDRD, $11 and the Port D Input Pins
– PIND, $10. The Port D Input Pins address is read-only, while the Data Register and
the Data Direction Register are read/write.
The Port D output buffers can sink 10 mA. As inputs, Port D pins that are externally
pulled low will source current if the pull-up resistors are activated.
All eight pins in Port D have equal functionality when used as digital I/O pins.
PDn, general I/O pin: The DDDn bit in the DDRD register selects the direction of this pin.
If DDDn is set (one), PDn is configured as an output pin. If DDDn is cleared (zero), PDn
is configured as an input pin. If PDn is set (one) when configured as an input pin, the
MOS pull-up resistor is activated. To switch the pull-up resistor off, the PDn has to be
cleared (zero), or the pin has to be configured as an output pin. The port pins are tri-
stated when a reset condition becomes active, even if the clock is not running.
Table 12. DDDn Bits on Port D Pins
Note:
DDDn
0
0
1
1
PBn
n: 7,6,...,0, pin number
MOS
PULL-
UP
PORTDn
RP:
n:
0
1
0
1
READ PORT B PIN
5 - 7
Output
Output
Input
Input
I/O
Pull-up
Yes
NO
No
No
Comment
Tri-state (high-Z)
PDn will source current if ext. pulled low
Push-pull Zero Output
Push-pull One Output
RP
TO LOW-LEVEL DETECTOR
PULL-UP PORT B
1062F–AVR–07/06