ATTINY28L-4AU Atmel, ATTINY28L-4AU Datasheet - Page 23

• Manufacturer Part Number: ATTINY28L-4AU
• Description: IC MCU AVR 2K FLASH 4MHZ 32-TQFP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY28L-4AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 4MHz
• Peripherals: POR, WDT
• Number Of I /o: 11
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFP, 32-VQFP
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 32 B
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 11
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Package: 32TQFP
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 4 MHz
• Ram Size: 32 Byte
• Operating Supply Voltage: 3.3|5 V
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIPATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Ram Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

Interrupt Flag Register – IFR
1062F–AVR–07/06
Table 8. Interrupt 1 Sense Control
Note:
• Bits 1, 0 – ISC01, ISC00: Interrupt Sense Control 0 Bit 1 and Bit 0
The External Interrupt 0 is activated by the external pin INT0 if the SREG I-flag and the
corresponding interrupt enable are set. The level and edges on the external INT0 pin
that activate the interrupt are defined in Table 9.
Table 9. Interrupt 0 Sense Control
Note:
The value on the INT pins are sampled before detecting edges. If edge interrupt is
selected, pulses that last longer than one CPU clock period will generate an interrupt.
Shorter pulses are not guaranteed to generate an interrupt. If low-level interrupt is
selected, the low level must be held until the completion of the currently executing
instruction to generate an interrupt. If enabled, a level-triggered interrupt will generate
an interrupt request as long as the pin is held low.
• Bit 7 – INTF1: External Interrupt Flag1
When an edge on the INT1 pin triggers an interrupt request, the corresponding interrupt
flag, INTF1 becomes set (one). If the I-bit in SREG and the corresponding interrupt
enable bit, INT1 in GIMSK is set (one), the MCU will jump to the interrupt vector. The
flag is cleared when the interrupt routine is executed. Alternatively, the flag can be
cleared by writing a logical “1” to it. This flag is always cleared when INT1 is configured
as level interrupt.
• Bit 6 – INTF0: External Interrupt Flag0
When an edge on the INT0 pin triggers an interrupt request, the corresponding interrupt
flag, INTF0 becomes set (one). If the I-bit in SREG and the corresponding interrupt
Bit
$05
Read/Write
Initial Value
ISC11
ISC01
0
0
1
1
0
0
1
1
When changing the ISC11/ISC10 bits, INT1 must be disabled by clearing its Interrupt
Enable bit. Otherwise, an interrupt can occur when the bits are changed.
When changing the ISC01/ISC00 bits, INT0 must be disabled by clearing its Interrupt
Enable bit. Otherwise, an interrupt can occur when the bits are changed.
ISC10
ISC00
INTF1
R/W
7
0
0
1
0
1
0
1
0
1
INTF0
R/W
Description
The low level of INT1 generates an interrupt request.
Any change on INT1 generates an interrupt request.
The falling edge of INT1 generates an interrupt request.
The rising edge of INT1 generates an interrupt request.
Description
The low level of INT0 generates an interrupt request.
Any change on INT0 generates an interrupt request.
The falling edge of INT0 generates an interrupt request.
The rising edge of INT0 generates an interrupt request.
6
0
R
5
–
0
TOV0
R/W
4
0
R
3
–
0
R
2
–
0
ATtiny28L/V
R
1
–
0
R
0
–
0
IFR
23