PIC16C770-I/P Microchip Technology, PIC16C770-I/P Datasheet - Page 49

• Manufacturer Part Number: PIC16C770-I/P
• Description: IC MCU CMOS A/D 2K 20MHZ 20-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C770-I/P

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Type: OTP
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 6x12b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16C
• No. Of I/o's: 16
• Ram Memory Size: 256Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• No. Of: RoHS Compliant
• Core: PIC
• Processor Series: PIC16C
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 20 MHz
• Data Ram Size: 256 B
• Data Rom Size: 256 B
• On-chip Adc: 6 bit
• Number Of Programmable I/os: 16
• Number Of Timers: 3 bit
• Operating Supply Voltage: 2.5 V to 5.5 V
• Mounting Style: Through Hole
• Height: 3.3 mm
• Interface Type: I2C, SPI, SSP
• Length: 26.16 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4 V
• Width: 6.35 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA16XP200 - ADAPTER ICE 20DIP/SOIC/SSOPAC164028 - MODULE SKT PROMATEII 20SOIC/DIP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC16C770I/P

6.0
The Timer1 module timer/counter has the following fea-
tures:
• 16-bit timer/counter
• Readable and writable (Both registers)
• Internal or external clock select
• Interrupt on overflow from FFFFh to 0000h
• RESET from ECCP module trigger
Timer1 has a control register, shown in Register 6-1.
Timer1 can be enabled/disabled by setting/clearing
control bit TMR1ON (T1CON<0>).
Figure 6-2 is a simplified block diagram of the Timer1
module.
REGISTER 6-1:
2002 Microchip Technology Inc.
(Two 8-bit registers; TMR1H and TMR1L)
TIMER1 MODULE
bit 7-6
bit 5-4
bit 3
bit 2
bit 1
bit 0
TIMER1 CONTROL REGISTER (T1CON: 10h)
Unimplemented: Read as '0'
T1CKPS<1:0>: Timer1 Input Clock Prescale Select bits
11 = 1:8 Prescale value
10 = 1:4 Prescale value
01 = 1:2 Prescale value
00 = 1:1 Prescale value
T1OSCEN: Timer1 Oscillator Enable Control bit
1 = Oscillator is enabled
0 = Oscillator is shut off
T1SYNC: Timer1 External Clock Input Synchronization Control bit
TMR1CS = 1:
1 = Do not synchronize external clock input
0 = Synchronize external clock input
TMR1CS = 0:
This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0.
TMR1CS: Timer1 Clock Source Select bit
1 = External clock from pin RB6/T1OSO/T1CKI /P1C (on the rising edge)
0 = Internal clock (F
TMR1ON: Timer1 On bit
1 = Enables Timer1
0 = Stops Timer1
Legend:
R = Readable bit
- n = Value at POR
bit 7
Note 1: The oscillator inverter and feedback resistor are turned off to eliminate power drain.
U-0
—
U-0
—
OSC
(1)
/4)
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC
R/W-0
W = Writable bit
’1’ = Bit is set
R/W-0
Additional information on timer modules is available in
the PICmicro™ Mid-Range MCU Family Reference
Manual, (DS33023).
6.1
Timer1 can operate in one of these modes:
• As a timer
• As a synchronous counter
• As an asynchronous counter
The Operating mode is determined by the clock select
bit, TMR1CS (T1CON<1>).
In Timer mode, Timer1 increments every instruction
cycle. In Counter mode, it increments on every rising
edge of the external clock input.
PIC16C717/770/771
Timer1 Operation
R/W-0
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
R/W-0
x = Bit is unknown
TMR1CS TMR1ON
R/W-0
DS41120B-page 47
R/W-0
bit 0