AT90USB82-16MUR Atmel, AT90USB82-16MUR Datasheet - Page 41

• Manufacturer Part Number: AT90USB82-16MUR
• Description: MCU AVR USB 8K FLASH 32-QFN
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB82-16MUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, PS/2, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-QFN
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, USART, debugWIRE
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK526 - KIT STARTER FOR AT90USB82/162ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK525 - KIT STARTER FOR AT90USBAT90USBKEY2 - KIT DEMO FOR AT90USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details

8. Power Management and Sleep Modes
8.0.1
7707F–AVR–11/10
Sleep Mode Control Register – SMCR
Sleep modes enable the application to shut down unused modules in the MCU, thereby saving
power. The AVR provides various sleep modes allowing the user to tailor the power consump-
tion to the application’s requirements.
To enter any of the five sleep modes, the SE bit in SMCR must be written to logic one and a
SLEEP instruction must be executed. The SM2, SM1, and SM0 bits in the SMCR Register select
which sleep mode (Idle, Power-down, Power-save, Standby or Extended standby) will be acti-
vated by the SLEEP instruction. See
while the MCU is in a sleep mode, the MCU wakes up. The MCU is then halted for four cycles in
addition to the start-up time, executes the interrupt routine, and resumes execution from the
instruction following SLEEP. The contents of the Register File and SRAM are unaltered when
the device wakes up from sleep. If a reset occurs during sleep mode, the MCU wakes up and
executes from the Reset Vector.
Figure 6-1 on page 25
distribution. The figure is helpful in selecting an appropriate sleep mode.
The Sleep Mode Control Register contains control bits for power management.
• Bit 7-4 - Reserved bits
These bits are reserved and will always read as zero.
• Bits 3-1 – SM2..0: Sleep Mode Select Bits 2, 1, and 0
These bits select between the five available sleep modes as shown in
Table 8-1.
Note:
• Bit 0– SE: Sleep Enable
The SE bit must be written to logic one to make the MCU enter the sleep mode when the SLEEP
instruction is executed. To avoid the MCU entering the sleep mode unless it is the programmer’s
Bit
Read/Write
Initial Value
SM2
0
0
0
0
1
1
1
1
1. Standby modes are only recommended for use with external crystals or resonators.
7
–
R
0
Sleep Mode Select
SM1
0
0
1
1
0
0
1
1
6
–
R
0
presents the different clock systems in the AT90USB82/162, and their
5
–
R
0
SM0
0
1
0
1
0
1
0
1
Table 8-1
4
–
R
0
Sleep Mode
Idle
Reserved
Power-down
Power-save
Reserved
Reserved
Standby
Extended Standby
for a summary. If an enabled interrupt occurs
3
SM2
R/W
0
(1)
2
SM1
R/W
0
(1)
AT90USB82/162
1
SM0
R/W
0
Table
8-1.
0
SE
R/W
0
SMCR
41