PIC16F886-E/SP Microchip Technology, PIC16F886-E/SP Datasheet - Page 251

• Manufacturer Part Number: PIC16F886-E/SP
• Description: IC PIC MCU FLASH 8KX14 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F886-E/SP

• Program Memory Type: FLASH
• Program Memory Size: 14KB (8K x 14)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 24
• Eeprom Size: 256 x 8
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: MSSP/EUSART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 3
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM164123, DM164120-3, DV164122
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM164123 - KIT MANAGEMENT SYSTEM PICDEMDVA18XP280 - DEVICE ADAPTER 18F2220 PDIP 28LD
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

17.8
FIGURE 17-4:
TABLE 17-1:
© 2007 Microchip Technology Inc.
Standard Operating Conditions (unless otherwise stated)
Operating temperature
OS01
OS02
OS03
OS04*
OS05*
Note 1:
Param
(LP,XT,HS Modes)
No.
OSC2/CLKOUT
OSC2/CLKOUT
(CLKOUT Mode)
OSC1/CLKIN
*
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and
AC Characteristics: PIC16F882/883/884/886/887 (Industrial, Extended)
F
T
T
TosH,
TosL
TosR,
TosF
OSC
CY
Sym
OSC
These parameters are characterized but not tested.
are not tested.
Instruction cycle period (T
based on characterization data for that particular oscillator type under standard operating conditions with the
device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or
higher than expected current consumption. All devices are tested to operate at “min” values with an external
clock applied to OSC1 pin. When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for
all devices.
External CLKIN Frequency
Oscillator Frequency
External CLKIN Period
Oscillator Period
Instruction Cycle Time
External CLKIN High,
External CLKIN Low
External CLKIN Rise,
External CLKIN Fall
CLOCK OSCILLATOR TIMING REQUIREMENTS
CLOCK TIMING
Characteristic
Q4
-40°C ≤ T
(1)
CY
(1)
) equals four times the input oscillator time base period. All specified values are
A
(1)
(1)
≤ +125°C
OS02
Q1
(1)
PIC16F882/883/884/886/887
Min
250
250
250
200
100
DC
DC
DC
DC
DC
0.1
Preliminary
27
50
50
50
20
—
—
1
2
0
0
0
Q2
32.768
Typ†
30.5
T
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
CY
OS03
10,000
OS04
1,000
Max
DC
37
20
20
20
—
—
—
—
—
—
4
4
4
•
•
•
•
•
•
•
Q3
OS04
Units
MHz
MHz
MHz
MHz
MHz
MHz
kHz
kHz
μs
μs
μs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
LP Oscillator mode
XT Oscillator mode
HS Oscillator mode
EC Oscillator mode
LP Oscillator mode
XT Oscillator mode
HS Oscillator mode
RC Oscillator mode
LP Oscillator mode
XT Oscillator mode
HS Oscillator mode
EC Oscillator mode
LP Oscillator mode
XT Oscillator mode
HS Oscillator mode
RC Oscillator mode
T
LP oscillator
XT oscillator
HS oscillator
LP oscillator
XT oscillator
HS oscillator
CY
Q4
= 4/F
OSC
Conditions
DS41291D-page 249
Q1