ATMEGA8L-8MUR Atmel, ATMEGA8L-8MUR Datasheet - Page 98

• Manufacturer Part Number: ATMEGA8L-8MUR
• Description: MCU AVR 8KB FLASH 8MHZ 32QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8L-8MUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 39. Waveform Generation Mode Bit Description (Continued)
Note:
Timer/Counter 1
Control Register B –
TCCR1B
98
Mode
10
11
12
13
14
15
7
8
9
1. The CTC1 and PWM11:0 bit definition names are obsolete. Use the
WGM13
ATmega8(L)
location of these bits are compatible with previous versions of the timer
0
1
1
1
1
1
1
1
1
WGM12
(CTC1)
1
0
0
0
0
1
1
1
1
• Bit 7 – ICNC1: Input Capture Noise Canceler
Setting this bit (to one) activates the Input Capture Noise Canceler. When the noise canceler is
activated, the input from the Input Capture Pin (ICP1) is filtered. The filter function requires four
successive equal valued samples of the ICP1 pin for changing its output. The Input Capture is
therefore delayed by four Oscillator cycles when the noise canceler is enabled.
• Bit 6 – ICES1: Input Capture Edge Select
This bit selects which edge on the Input Capture Pin (ICP1) that is used to trigger a capture
event. When the ICES1 bit is written to zero, a falling (negative) edge is used as trigger, and
when the ICES1 bit is written to one, a rising (positive) edge will trigger the capture.
When a capture is triggered according to the ICES1 setting, the counter value is copied into the
Input Capture Register (ICR1). The event will also set the Input Capture Flag (ICF1), and this
can be used to cause an Input Capture Interrupt, if this interrupt is enabled.
When the ICR1 is used as TOP value (see description of the WGM13:0 bits located in the
TCCR1A and the TCCR1B Register), the ICP1 is disconnected and consequently the Input Cap-
ture function is disabled.
• Bit 5 – Reserved Bit
This bit is reserved for future use. For ensuring compatibility with future devices, this bit must be
written to zero when TCCR1B is written.
• Bit 4:3 – WGM13:2: Waveform Generation Mode
See TCCR1A Register description.
• Bit 2:0 – CS12:0: Clock Select
The three clock select bits select the clock source to be used by the Timer/Counter, see
41 on page 94
Bit
Read/Write
Initial Value
(PWM11)
WGM11
1
0
0
1
1
0
0
1
1
ICNC1
(PWM10)
R/W
and
WGM10
7
0
1
0
1
0
1
0
1
0
1
Figure 42 on page
ICES1
R/W
6
0
Timer/Counter Mode of
Operation
Fast PWM, 10-bit
PWM, Phase and Frequency Correct
PWM, Phase and Frequency Correct
PWM, Phase Correct
PWM, Phase Correct
CTC
(Reserved)
Fast PWM
Fast PWM
R
5
–
0
(1)
WGM13
94.
R/W
0
4
WGM12
WGM
R/W
3
0
12:0 definitions. However, the functionality and
CS12
R/W
2
0
TOP
0x03FF
ICR1
OCR1A
ICR1
OCR1A
ICR1
–
ICR1
OCR1A
CS11
R/W
1
0
Update of
OCR1
BOTTOM
BOTTOM
BOTTOM
TOP
TOP
Immediate
–
BOTTOM
BOTTOM
CS10
R/W
0
0
x
TCCR1B
2486Z–AVR–02/11
TOV1 Flag
Set on
TOP
BOTTOM
BOTTOM
MAX
–
TOP
BOTTOM
BOTTOM
TOP
Figure