PIC18LF4685-I/P Microchip Technology, PIC18LF4685-I/P Datasheet - Page 229

• Manufacturer Part Number: PIC18LF4685-I/P
• Description: IC PIC MCU FLASH 48KX16 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF4685-I/P

• Core Size: 8-Bit
• Program Memory Size: 96KB (48K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.25K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3.25KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Package: 40PDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 44
• Interface Type: CAN/I2C/SPI/USART
• On-chip Adc: 11-chx10-bit
• Number Of Timers: 4
• Core: PIC
• Processor Series: PIC18LF
• Maximum Clock Frequency: 40 MHz
• Data Ram Size: 3.25 KB
• Mounting Style: Through Hole
• A/d Bit Size: 10 bit
• A/d Channels Available: 11
• Height: 4.95 mm
• Length: 53.21 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2 V
• Width: 14.73 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

18.0
The Enhanced Universal Synchronous Asynchronous
Receiver Transmitter (EUSART) module is one of the
two serial I/O modules. (USART is also known as a
Serial Communications Interface or
EUSART can be configured as a full-duplex asynchro-
nous system that can communicate with peripheral
devices, such as CRT terminals and personal comput-
ers. It can also be configured as a half-duplex synchro-
nous system that can communicate with peripheral
devices, such as A/D or D/A integrated circuits, serial
EEPROMs and so on.
The EUSART module implements additional features,
including Auto-Baud Rate Detection and calibration,
automatic wake-up on Sync Break reception and 12-bit
Break character transmit. These features make it
ideally suited for use in Local Interconnect Network bus
(LIN bus) systems.
The EUSART can be configured in the following
modes:
• Asynchronous (full duplex) with:
• Synchronous – Master (half duplex) with
• Synchronous – Slave (half duplex) with
© 2009 Microchip Technology Inc.
- Auto-Wake-up on Character Reception
- Auto-Baud Calibration
- 12-Bit Break Character Transmission
Selectable Clock Polarity
Selectable Clock Polarity
ENHANCED UNIVERSAL
SYNCHRONOUS RECEIVER
TRANSMITTER (EUSART)
SCI.)
PIC18F2682/2685/4682/4685
The
The pins of the Enhanced USART are multiplexed
with PORTC. In order to configure RC6/TX/CK and
RC7/RX/DT as an EUSART:
• bit SPEN (RCSTA<7>) must be set (= 1)
• bit TRISC<7> must be set (= 1)
• bit TRISC<6> must be cleared (= 0) for
The operation of the Enhanced USART module is
controlled through three registers:
• Transmit Status and Control (TXSTA)
• Receive Status and Control (RCSTA)
• Baud Rate Control (BAUDCON)
These are detailed on the following pages in
Register 18-1,
respectively.
Asynchronous and Synchronous Master modes,
or set (= 1) for Synchronous Slave mode
Note:
The EUSART control will automatically
reconfigure the pin from input to output as
needed.
Register 18-2
and
DS39761C-page 229
Register 18-3,