C8051F310-GQR Silicon Laboratories Inc, C8051F310-GQR Datasheet - Page 164
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
C8051F310-GQR
Manufacturer Part Number
C8051F310-GQR
Description
IC 8051 MCU 16K FLASH 32LQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F31xr
Specifications of C8051F310-GQR
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
POR, PWM, Temp Sensor, WDT
Number Of I /o
29
Program Memory Size
16KB (16K x 8)
Program Memory Type
FLASH
Ram Size
1.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 21x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
32-LQFP
For Use With
336-1445 - ADAPTER PROGRAM TOOLSTICK F310336-1329 - KIT REF DESIGN SENSORLESS BLDC336-1253 - DEV KIT FOR C8051F310/F311
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F310-GQR
Manufacturer:
SILICON
Quantity:
3 300
Company:
Part Number:
C8051F310-GQR
Manufacturer:
SILICON41
Quantity:
120
Company:
Part Number:
C8051F310-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
C8051F310-GQR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
C8051F310/1/2/3/4/5/6/7
15.1. Enhanced Baud Rate Generation
The UART0 baud rate is generated by Timer 1 in 8-bit auto-reload mode. The TX clock is generated by
TL1; the RX clock is generated by a copy of TL1 (shown as RX Timer in Figure 15.2), which is not user-
accessible. Both TX and RX Timer overflows are divided by two to generate the TX and RX baud rates.
The RX Timer runs when Timer 1 is enabled, and uses the same reload value (TH1). However, an
RX Timer reload is forced when a START condition is detected on the RX pin. This allows a receive to
begin any time a START is detected, independent of the TX Timer state.
Timer 1 should be configured for Mode 2, 8-bit auto-reload (see
ter/Timer with Auto-Reload” on page
occur at two times the desired UART baud rate frequency. Note that Timer 1 may be clocked by one of six
sources: SYSCLK, SYSCLK / 4, SYSCLK / 12, SYSCLK / 48, the external oscillator clock / 8, or an exter-
nal input T1. For any given Timer 1 clock source, the UART0 baud rate is determined by Equation 15.1.
Where T1
value). Timer 1 clock frequency is selected as described in
reference for typical baud rates and system clock frequencies is given in Table 15.1 through Table 15.6.
Note that the internal oscillator may still generate the system clock when the external oscillator is driving
Timer 1.
164
CLK
is the frequency of the clock supplied to Timer 1, and T1H is the high byte of Timer 1 (reload
Detected
Start
Figure 15.2. UART0 Baud Rate Logic
RX Timer
Equation 15.1. UART0 Baud Rate
UartBaudRate
Timer 1
TH1
TL1
189). The Timer 1 reload value should be set so that overflows will
Overflow
Overflow
Rev. 1.7
=
------------------------------ -
256 T1H
T1
–
Section “17. Timers” on page
CLK
2
2
Section “17.1.3. Mode 2: 8-bit Coun-
UART
1
-- -
2
RX Clock
TX Clock
187. A quick