ST72F324BK4T3 STMicroelectronics, ST72F324BK4T3 Datasheet - Page 192

• Manufacturer Part Number: ST72F324BK4T3
• Description: IC MCU 8BIT 16K FLASH 32-TQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F324BK4T3

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 32-TQFP, 32-VQFP
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7232X-EVAL, ST7MDT20-DVP3, ST7MDT20J-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• A/d Bit Size: 10 bit
• A/d Channels Available: 12
• Height: 1.4 mm
• Length: 7 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 3.8 V
• Width: 7 mm
• For Use With: 497-6421 - BOARD EVAL DGTL BATT CHGR DESIGN497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-8241; ST72F324BK4T3

Known limitations
15.1.5
15.1.6
15.1.7
192/198
Nested interrupt context
The symptom does not occur when the interrupts are handled normally, that is, when:
●
●
●
If these conditions are not met, the symptom can be avoided by implementing the following
sequence:
16-bit timer PWM mode
In PWM mode, the first PWM pulse is missed after writing the value FFFCh in the OC1R
register (OC1HR, OC1LR). It leads to either full or no PWM during a period, depending on
the OLVL1 and OLVL2 settings.
TIMD set simultaneously with OC interrupt
If the 16-bit timer is disabled at the same time the output compare event occurs then output
compare flag gets locked and cannot be cleared before the timer is enabled again.
Impact on the application
If output compare interrupt is enabled, then the output compare flag cannot be cleared in the
timer interrupt routine. Consequently the interrupt service routine is called repeatedly.
Workaround
Disable the timer interrupt before disabling the timer. Again while enabling, first enable the
timer then the timer interrupts.
●
●
SCI wrong break duration
Description
A single break character is sent by setting and resetting the SBK bit in the SCICR2 register.
In some cases, the break character may have a longer duration than expected:
●
●
The interrupt flag is cleared within its own interrupt routine
The interrupt flag is cleared within any interrupt routine with higher or identical priority
level
The interrupt flag is cleared in any part of the code while this interrupt is disabled
–
–
–
–
Perform the following to disable the timer:
–
–
Perform the following to enable the timer again:
–
–
20 bits instead of 10 bits if M = 0
22 bits instead of 11 bits if M = 1
PUSH CC
SIM
Reset interrupt flag
POP CC
TACR1 or TBCR1 = 0x00h; // Disable the compare interrupt
TACSR I or TBCSR I = 0x40; // Disable the timer
TACSR & or TBCSR & = ~0x40; // Enable the timer
TACR1 or TBCR1 = 0x40; // Enable the compare interrupt
Doc ID13466 Rev 4
ST72324B-Auto