PIC18F442-I/L Microchip Technology, PIC18F442-I/L Datasheet - Page 19

• Manufacturer Part Number: PIC18F442-I/L
• Description: IC MCU FLASH 8KX16 EE A/D 44PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F442-I/L

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-PLCC
• Controller Family/series: PIC18
• No. Of I/o's: 34
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: MSSP, SPI, I2C, PSP, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 34
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8
• Package: 44PLCC
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164309 - MODULE SKT FOR PM3 44PLCCXLT44L2 - SOCKET TRAN ICE 44PLCC444-1001 - DEMO BOARD FOR PICMICRO MCUDVA16XL441 - ADAPTER DEVICE ICE 44PLCCDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Lead Free Status / Rohs Status: Details
• Other names: PIC18F442I/L

2.0
2.1
The PIC18FXX2 can be operated in eight different
Oscillator modes. The user can program three configu-
ration bits (FOSC2, FOSC1, and FOSC0) to select one
of these eight modes:
1.
2.
3.
4.
5.
6.
7.
8.
2.2
In XT, LP, HS or HS+PLL Oscillator modes, a crystal or
ceramic resonator is connected to the OSC1 and
OSC2 pins to establish oscillation. Figure 2-1 shows
the pin connections.
The PIC18FXX2 oscillator design requires the use of a
parallel cut crystal.
FIGURE 2-1:
© 2006 Microchip Technology Inc.
Note:
Note 1: See
LP
XT
HS
HS + PLL
RC
RCIO
EC
ECIO
C1
C2
OSCILLATOR
CONFIGURATIONS
Oscillator Types
Crystal Oscillator/Ceramic
Resonators
(1)
(1)
2: A series resistor (R
3: R
Use of a series cut crystal may give a fre-
quency out of the crystal manufacturers
specifications.
recommended values of C1 and C2.
AT strip cut crystals.
XTAL
R
F
S
(2)
varies with the Oscillator mode chosen.
with PLL enabled
enabled
Low Power Crystal
Crystal/Resonator
High Speed Crystal/Resonator
High Speed Crystal/Resonator
External Resistor/Capacitor
External Resistor/Capacitor with
I/O pin enabled
External Clock
External
OSC2
OSC1
Table 2-1
CRYSTAL/CERAMIC
RESONATOR OPERATION
(HS, XT OR LP
CONFIGURATION)
Clock
R
S
and
F
) may be required for
(3)
with
Table 2-2
SLEEP
PIC18FXXX
I/O
To
Internal
Logic
for
pin
TABLE 2-1:
These values are for design guidance only.
See notes following this table.
All resonators used did not have built-in capacitors.
16.0 MHz Murata Erie CSA16.00MX
455 kHz Panasonic EFO-A455K04B
2.0 MHz Murata Erie CSA2.00MG
4.0 MHz Murata Erie CSA4.00MG
8.0 MHz Murata Erie CSA8.00MT
Mode
Note 1: Higher capacitance increases the stability
HS
XT
2: When operating below 3V V
3: Since each resonator/crystal has its own
of the oscillator, but also increases the
start-up time.
using certain ceramic resonators at any
voltage, it may be necessary to use
high-gain HS mode, try a lower frequency
resonator, or switch to a crystal oscillator.
characteristics, the user should consult the
resonator/crystal manufacturer for appro-
priate values of external components, or
verify oscillator performance.
16.0 MHz
455 kHz
2.0 MHz
4.0 MHz
8.0 MHz
Freq
Resonators Used:
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
Ranges Tested:
PIC18FXX2
68 - 100 pF
15 - 68 pF
15 - 68 pF
10 - 68 pF
10 - 22 pF
C1
DS39564C-page 17
DD
68 - 100 pF
15 - 68 pF
15 - 68 pF
10 - 68 pF
10 - 22 pF
, or when
0.3%
0.5%
0.5%
0.5%
0.5%
C2