PIC18C801-I/PT Microchip Technology, PIC18C801-I/PT Datasheet - Page 205

• Manufacturer Part Number: PIC18C801-I/PT
• Description: IC PIC MCU ROMLESS 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C801-I/PT

• Core Size: 8-Bit
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 25MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Number Of I /o: 37
• Program Memory Type: ROMless
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 67
• Ram Memory Size: 1.5KB
• Cpu Speed: 6.25MIPS
• No. Of Timers: 4
• Program Memory Size: EXT
• Processor Series: PIC18C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: 3-Wire, I2C, SPI, USART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 47
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: DV164005, ICE4000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT80PT3 - SOCKET TRAN ICE 80MQFP/TQFPAC164320 - MODULE SKT MPLAB PM3 80TQFPAC174011 - MODULE SKT PROMATEII 80TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC18C801I/PT

18.2
Depending on the power source for the device voltage,
the voltage normally decreases relatively slowly. This
means that the LVD module does not need to be con-
stantly operating. To decrease current consumption,
the LVD circuitry only needs to be enabled for short
periods, where the voltage is checked. After doing the
check, the LVD module may be disabled.
Each time that the LVD module is enabled, the circuitry
requires some time to stabilize. After the circuitry has
stabilized, all status flags may be cleared. The module
will then indicate the proper state of the system.
FIGURE 18-3:
2001 Microchip Technology Inc.
Internally Generated
Internally Generated
Reference Stable
Reference Stable
Operation
CASE 1:
CASE 2:
Enable LVD
Enable LVD
LVDIF
LVDIF
V
V
DD
DD
LOW VOLTAGE DETECT WAVEFORMS
Advance Information
50 ms
50 ms
LVDIF may not be set
The following steps are needed to setup the LVD
module:
1.
2.
3.
4.
5.
6.
Figure 18-3 shows typical waveforms that the LVD
module may be used to detect.
LVDIF cleared in software,
LVDIF remains set since LVD condition still exists
Write the value to the LVDL3:LVDL0 bits
(LVDCON register), which selects the desired
LVD trip point.
Ensure that LVD interrupts are disabled (the
LVDIE bit is cleared or the GIE bit is cleared).
Enable the LVD module (set the LVDEN bit in
the LVDCON register).
Wait for the LVD module to stabilize (the IRVST
bit to become set).
Clear the LVD interrupt flag, which may have
falsely become set, until the LVD module has
stabilized (clear the LVDIF bit).
Enable the LVD interrupt (set the LVDIE and the
GIE bits).
PIC18C601/801
LVDIF cleared in software
LVDIF cleared in software
DS39541A-page 205
V
V
LVD
LVD