PIC18F46J50-I/ML Microchip Technology, PIC18F46J50-I/ML Datasheet - Page 393

• Manufacturer Part Number: PIC18F46J50-I/ML
• Description: IC PIC MCU FLASH 64KB 44-QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F46J50-I/ML

• Program Memory Type: FLASH
• Program Memory Size: 64KB (32K x 16)
• Package / Case: 44-QFN
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 34
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Timers: 2
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183032, DV164136, MA180024, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 13 Channel
• Package: 44QFN EP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• A/d Bit Size: 10 bit
• A/d Channels Available: 13
• Height: 0.88 mm
• Length: 8 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.15 V
• Width: 8 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

24.2
To set up the HLVD module:
1.
2.
3.
4.
5.
6.
24.3
When the module is enabled, the HLVD comparator
and voltage divider are enabled and will consume static
current. The total current consumption, when enabled,
is specified in electrical specification parameter D022B
(ΔI
Down and Supply Current
(Industrial)”).
Depending on the application, the HLVD module does
not need to operate constantly. To decrease the current
requirements, the HLVD circuitry may only need to be
enabled for short periods where the voltage is checked.
After doing the check, the HLVD module may be
disabled.
© 2009 Microchip Technology Inc.
HLVD
Disable the module by clearing the HLVDEN bit
(HLVDCON<4>).
Write the value to the HLVDL<3:0> bits that
selects the desired HLVD trip point.
Set the VDIRMAG bit to detect one of the
following:
• High voltage (VDIRMAG = 1)
• Low voltage (VDIRMAG = 0)
Enable the HLVD module by setting the
HLVDEN bit.
Clear the HLVD Interrupt Flag, HLVDIF
(PIR2<2>), which may have been set from a
previous interrupt.
If interrupts are desired, enable the HLVD inter-
rupt by setting the HLVDIE and GIE/GIEH bits
(PIE2<2> and INTCON<7>).
An interrupt will not be generated until the
IRVST bit is set.
) (Section 29.2 “DC Characteristics: Power-
HLVD Setup
Current Consumption
PIC18F46J50 Family
PIC18F46J50 FAMILY
24.4
The internal reference voltage of the HLVD module,
specified
D420(see Table 29-8 in Section 29.0 “Electrical
Characteristics”), may be used by other internal cir-
cuitry, such as the Programmable Brown-out Reset
(BOR).
If the HLVD or other circuits using the voltage reference
are disabled to lower the device’s current consumption,
the reference voltage circuit will require time to become
stable before a low or high-voltage condition can be
reliably detected. This start-up time, T
interval that is independent of device clock speed. It is
specified in electrical specification parameter 36
(Table 29-13).
The HLVD interrupt flag is not enabled until T
expired and a stable reference voltage is reached. For
this reason, brief excursions beyond the set point may
not be detected during this interval. Refer to Figure 24-2
or Figure 24-3.
HLVD Start-up Time
in
electrical
specification
DS39931C-page 393
IRVST
parameter
IRVST
, is an
has