ATMEGA8535L-8JU Atmel, ATMEGA8535L-8JU Datasheet - Page 226

• Manufacturer Part Number: ATMEGA8535L-8JU
• Description: MCU AVR 8K ISP FLASH MEM 44-PLCC
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8535L-8JU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-PLCC
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 8MHz
• Total Internal Ram Size: 512Byte
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: PLCC
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Boot Loader Lock Bits
226
ATmega8535(L)
Figure 113. Memory sections
Note:
If no Boot Loader capability is needed, the entire Flash is available for application code.
The Boot Loader has two separate sets of Boot Lock bits which can be set indepen-
dently. This gives the user a unique flexibility to select different levels of protection.
The user can select:
•
•
•
•
See Table 89 and Table 90 for further details. The Boot Lock bits can be set in software
and in Serial or Parallel Programming mode, but they can be cleared by a Chip Erase
command only. The general Write Lock (Lock Bit mode 2) does not control the program-
ming of the Flash memory by SPM instruction. Similarly, the general Read/Write Lock
(Lock Bit mode 1) does not control reading nor writing by LPM/SPM, if it is attempted.
To protect the entire Flash from a software update by the MCU.
To protect only the Boot Loader Flash section from a software update by the MCU.
To protect only the Application Flash section from a software update by the MCU.
Allow software update in the entire Flash.
1. The parameters in the figure above are given in Table 93 on page 235.
Boot Loader Flash Section
Boot Loader Flash Section
Application Flash Section
Application Flash Section
Application Flash Section
Application Flash Section
Program Memory
Program Memory
BOOTSZ = '11'
BOOTSZ = '01'
$0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
$0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
(1)
Boot Loader Flash Section
Boot Loader Flash Section
Application Flash Section
Application Flash Section
Application Flash Section
Program Memory
Program Memory
BOOTSZ = '10'
BOOTSZ = '00'
$0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
$0000
End RWW, End Application
Start NRWW, Start Boot Loader
Flashend
2502K–AVR–10/06