ATMEGA8535L-8JU Atmel, ATMEGA8535L-8JU Datasheet - Page 147

• Manufacturer Part Number: ATMEGA8535L-8JU
• Description: MCU AVR 8K ISP FLASH MEM 44-PLCC
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8535L-8JU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-PLCC
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 8MHz
• Total Internal Ram Size: 512Byte
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: PLCC
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Internal Clock Generation –
The Baud Rate Generator
2502K–AVR–10/06
Figure 70. Clock Generation Logic, Block Diagram
Signal description:
Internal clock generation is used for the asynchronous and the synchronous master
modes of operation. The description in this section refers to Figure 70.
The USART Baud Rate Register (UBRR) and the down-counter connected to it function
as a programmable prescaler or baud rate generator. The down-counter, running at sys-
tem clock (fosc), is loaded with the UBRR value each time the counter has counted
down to zero or when the UBRRL Register is written. A clock is generated each time the
cou nter rea ches zero. Th is clock is the bau d r ate gen erato r clock outp ut
(= fosc/(UBRR+1)). The Transmitter divides the baud rate generator clock output by 2,
8, or 16 depending on mode. The baud rate generator output is used directly by the
receiver’s clock and data recovery units. However, the recovery units use a state
machine that uses 2, 8, or 16 states depending on mode set by the state of the UMSEL,
U2X and DDR_XCK bits.
Table 61 contains equations for calculating the baud rate (in bits per second) and for
calculating the UBRR value for each mode of operation using an internally generated
clock source.
txclk
rxclk
xcki
xcko
fosc
DDR_XCK
XCK
Pin
Transmitter clock (Internal Signal).
Receiver base clock (Internal Signal).
Input from XCK pin (internal Signal). Used for synchronous slave operation.
Clock output to XCK pin (Internal Signal). Used for synchronous master
operation.
XTAL pin frequency (System Clock).
xcko
xcki
OSC
Down-Counter
Prescaling
Register
UBRR
Sync
UBRR+1
fosc
Detector
UCPOL
Edge
/ 2
/ 4
ATmega8535(L)
/ 2
DDR_XCK
U2X
0
1
0
1
0
1
1
0
UMSEL
txclk
rxclk
147