PIC16F1938-I/ML Microchip Technology, PIC16F1938-I/ML Datasheet - Page 335

• Manufacturer Part Number: PIC16F1938-I/ML
• Description: IC MCU 8BIT FLASH 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1938-I/ML

• Core Size: 8-Bit
• Program Memory Size: 28KB (16K x 14)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC16F
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 1024Byte
• Cpu Speed: 32MHz
• Package: 28QFN EP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 32 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 25
• Interface Type: I2C/SPI/USART
• On-chip Adc: 11-chx10-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

24.0
The Power-down mode is entered by executing a
SLEEP instruction.
If the Watchdog Timer is enabled:
• WDT will be cleared but keeps running.
• PD bit of the STATUS register is cleared.
• TO bit of the STATUS register is set.
• Oscillator driver is turned off.
• Timer1 oscillator is unaffected
• I/O ports maintain the status they had before
For lowest current consumption in this mode, all I/O
pins should be either at V
circuitry drawing current from the I/O pin. I/O pins that
are high-impedance inputs should be pulled high or low
externally to avoid switching currents caused by float-
ing inputs. The T0CKI input should also be at V
V
from on-chip pull-ups on PORTB should be considered.
Enabled Resets remain functional during Sleep.
24.1
The device can wake-up from Sleep through one of the
following events:
1.
2.
3.
4.
5.
The first two events will cause a device Reset. The last
three events are considered a continuation of program
execution. The TO and PD bits in the STATUS register
can be used to determine the cause of device Reset.
The PD bit, which is set on power-up, is cleared when
Sleep is invoked. TO bit is cleared if WDT wake-up
occurred.
Certain peripherals cannot generate interrupts since
during Sleep, no on-chip clocks are present.
When the SLEEP instruction is being executed, the next
instruction (PC + 1) is prefetched. For the device to
wake-up through an interrupt event, the corresponding
interrupt enable bit must be set (enabled). Wake-up is
regardless of the state of the GIE bit. If the GIE bit is
clear (disabled), the device continues execution at the
instruction after the SLEEP instruction. If the GIE bit is
set (enabled), the device executes the instruction after
the SLEEP instruction, then branches to the interrupt
© 2009 Microchip Technology Inc.
SS
SLEEP was executed (driving high, low or high-
impedance).
External Reset input on MCLR pin, if enabled.
BOR Reset, if enabled.
Watchdog
enabled).
Any external interrupt.
Certain peripheral interrupts (see individual
peripheral for more information).
for lowest current consumption. The contribution
POWER-DOWN MODE (SLEEP)
Wake-up from Sleep
Timer
wake-up
DD
or V
SS
(if
, with no external
WDT
was
DD
Preliminary
or
address (0004h). In cases where the execution of the
instruction following SLEEP is not desirable, the user
should have a NOP after the SLEEP instruction.
The WDT is cleared when the device wakes up from
Sleep, regardless of the source of wake-up.
PIC16F193X/LF193X
Note:
If the global interrupts are disabled (GIE is
cleared), but any interrupt source has both
its interrupt enable bit and the correspond-
ing interrupt flag bits set, the device will
immediately wake-up from Sleep. The
SLEEP instruction is completely executed.
DS41364C-page 335