PIC12F519-I/SN Microchip Technology, PIC12F519-I/SN Datasheet - Page 18

• Manufacturer Part Number: PIC12F519-I/SN
• Description: IC PIC MCU FLASH 1KX12 8SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12F519-I/SN

• Program Memory Type: FLASH
• Program Memory Size: 1.5KB (1K x 12)
• Package / Case: 8-SOIC (3.9mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Ram Size: 41 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC12F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 41 B
• Interface Type: USB
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• Height: 1.25 mm
• Length: 4.9 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2 V
• Width: 3.9 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC12F519
4.3
This register contains the arithmetic status of the ALU,
the Reset status and the page preselect bit.
The STATUS register can be the destination for any
instruction, as with any other register. If the STATUS
register is the destination for an instruction that affects
the Z, DC or C bits, then the write to these three bits is
disabled. These bits are set or cleared according to the
device logic. Furthermore, the TO and PD bits are not
writable. Therefore, the result of an instruction with the
STATUS register as destination may be different than
intended.
REGISTER 4-1:
DS41319B-page 16
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
GPWUF
R/W-0
STATUS register
GPWUF: Wake-up From Sleep on Pin Change bit
1 = Reset due to wake-up from Sleep on pin change
0 = After power-up or other Reset
Unimplemented: Read as ‘
PA0: Program Page Preselect bit
1 = Page 1 (000h-1FFh)
0 = Page 0 (200h-3FFh)
TO: Time-out bit
1 = After power-up, CLRWDT instruction, or SLEEP instruction
0 = A WDT time-out occurred
PD: Power-down bit
1 = After power-up or by the CLRWDT instruction
0 = By execution of the SLEEP instruction
Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
DC: Digit carry/borrow bit (for ADDWF and SUBWF instructions)
ADDWF:
1 = A carry from the 4th low-order bit of the result occurred
0 = A carry from the 4th low-order bit of the result did not occur
SUBWF:
1 = A borrow from the 4th low-order bit of the result did not occur
0 = A borrow from the 4th low-order bit of the result occurred
C: Carry/borrow bit (for ADDWF, SUBWF and RRF, RLF instructions)
ADDWF:
1 = A carry occurred
0 = A carry did not occur
U-0
—
STATUS: STATUS REGISTER
W = Writable bit
‘1’ = Bit is set
R/W-0
PA0
0’
SUBWF:
1 = A borrow did not occur
0 = A borrow occurred
R-1
TO
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
For example, CLRF STATUS, will clear the upper three
bits and set the Z bit. This leaves the STATUS register
as ‘000u u1uu’ (where u = unchanged).
Therefore, it is recommended that only BCF, BSF and
MOVWF instructions be used to alter the STATUS regis-
ter. These instructions do not affect the Z, DC or C bits
from the STATUS register. For other instructions which
do affect Status bits, see Section 9.0 “Instruction Set
Summary”.
R-1
PD
RRF or RLF:
Load bit with LSb or MSb, respectively
R/W-x
Z
© 2008 Microchip Technology Inc.
x = Bit is unknown
R/W-x
DC
R/W-x
C
bit 0