ADE7753ARSZ Analog Devices Inc, ADE7753ARSZ Datasheet - Page 7

• Manufacturer Part Number: ADE7753ARSZ
• Description: IC ENERGY METERING 1PHASE 20SSOP
• Manufacturer: Analog Devices Inc

Specifications of ADE7753ARSZ

• Input Impedance: 390 KOhm
• Measurement Error: 0.1%
• Voltage - I/o High: 2.4V
• Voltage - I/o Low: 0.8V
• Current - Supply: 3mA
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-SSOP (0.200", 5.30mm Width)
• Meter Type: Single Phase
• Ic Function: Single-Phase Multifunction Metering IC
• Supply Voltage Range: 4.75V To 5.25V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: SSOP
• No. Of Pins: 20
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADE7753ZEB - BOARD EVALUATION AD7753
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

TERMINOLOGY
Measurement Error
The error associated with the energy measurement made by the
ADE7753 is defined by the following formula:
Phase Error between Channels
The digital integrator and the high-pass filter (HPF) in Channel 1
have a non-ideal phase response. To offset this phase response
and equalize the phase response between channels, two phase-
correction networks are placed in Channel 1: one for the digital
integrator and the other for the HPF. The phase correction
networks correct the phase response of the corresponding
component and ensure a phase match between Channel 1
(current) and Channel 2 (voltage) to within ±0.1° over a range
of 45 Hz to 65 Hz with the digital integrator off. With the
digital integrator on, the phase is corrected to within ±0.4°
over a range of 45 Hz to 65 Hz.
Power Supply Rejection
This quantifies the ADE7753 measurement error as a percentage
of reading when the power supplies are varied. For the ac PSR
measurement, a reading at nominal supplies (5 V) is taken. A
second reading is obtained with the same input signal levels
when an ac (175 mV rms/120 Hz) signal is introduced onto the
Percentage
Error
=
⎛
⎜ ⎜
⎝
Energy
Register
True
ADE
Energy
7753
−
True
Energy
⎞
× ⎟ ⎟
⎠
100
Rev. A | Page 7 of 60
%
supplies. Any error introduced by this ac signal is expressed as
a percentage of reading—see the Measurement Error definition.
For the dc PSR measurement, a reading at nominal supplies
(5 V) is taken. A second reading is obtained with the same input
signal levels when the supplies are varied ±5%. Any error
introduced is again expressed as a percentage of the reading.
ADC Offset Error
The dc offset associated with the analog inputs to the ADCs. It
means that with the analog inputs connected to AGND, the
ADCs still see a dc analog input signal. The magnitude of the
offset depends on the gain and input range selection—see the
Typical Performance Characteristics section. However, when
HPF1 is switched on, the offset is removed from Channel 1
(current) and the power calculation is not affected by this
offset. The offsets can be removed by performing an offset
calibration—see the Analog Inputs section.
Gain Error
The difference between the measured ADC output code (minus
the offset) and the ideal output code—see the Channel 1 ADC
and Channel 2 ADC sections. It is measured for each of the
input ranges on Channel 1 (0.5 V, 0.25 V, and 0.125 V). The
difference is expressed as a percentage of the ideal code.
ADE7753