XCF16PVO48C XILINX [Xilinx, Inc], XCF16PVO48C Datasheet - Page 8

• Manufacturer Part Number: XCF16PVO48C
• Description: Platform Flash In-System Programmable Configuration PROMs
• Manufacturer: XILINX [Xilinx, Inc]

Table 7: XCFxxS Instruction Capture Values Loaded into IR as part of an Instruction Scan Sequence
Table 8: XCFxxP Instruction Capture Values Loaded into IR as part of an Instruction Scan Sequence
Boundary Scan Register
The boundary-scan register is used to control and observe
the state of the device pins during the EXTEST,
SAMPLE/PRELOAD, and CLAMP instructions. Each output
pin on the Platform Flash PROM has two register stages
which contribute to the boundary-scan register, while each
input pin has only one register stage. The bidirectional pins
have a total of three register stages which contribute to the
boundary-scan register. For each output pin, the register
stage nearest to TDI controls and observes the output state,
and the second stage closest to TDO controls and observes
the High-Z enable state of the output pin. For each input pin,
a single register stage controls and observes the input state
of the pin. The bidirectional pin combines the three bits, the
input stage bit is first, followed by the output stage bit and
finally the output enable stage bit. The output enable stage
bit is closest to TDO.
See the XCFxxS/XCFxxP Pin Names and Descriptions
Tables in the
for the boundary-scan bit order for all connected device pins,
or see the appropriate BSDL file for the complete
boundary-scan bit order description under the "attribute
BOUNDARY_REGISTER" section in the BSDL file. The bit
assigned to boundary-scan cell 0 is the LSB in the
boundary-scan register, and is the register bit closest to TDO.
Identification Registers
IDCODE Register
The IDCODE is a fixed, vendor-assigned value that is used
to electrically identify the manufacturer and type of the
device being addressed. The IDCODE register is 32 bits
wide. The IDCODE register can be shifted out for
examination by using the IDCODE instruction. The IDCODE
is available to any other system component via JTAG.
Table 9
Flash PROMs.
The IDCODE register has the following binary format:
where
DS123 (v2.11.1) March 30, 2007
Product Specification
TDI →
TDI →
vvvv:ffff:ffff:aaaa:aaaa:cccc:cccc:ccc1
v = the die version number
f = the PROM family code
a = the specific Platform Flash PROM product ID
c = the Xilinx manufacturer's ID
lists the IDCODE register values for the Platform
R
"Pinouts and Pin Descriptions," page 37
Reserved
IR[15:9]
Reserved
IR[7:5]
ISC Error
IR[8:7]
ISC Status
IR[4]
ER/PROG
IR[6:5]
Error
section
www.xilinx.com
Platform Flash In-System Programmable Configuration PROMs
ER/PROG
Security
Status
IR[4]
IR[3]
The LSB of the IDCODE register is always read as logic 1
as defined by IEEE Std. 1149.1.
Table 9: IDCODES Assigned to Platform Flash PROMs
USERCODE Register
The USERCODE instruction gives access to a 32-bit user
programmable scratch pad typically used to supply
information about the device's programmed contents. By
using the USERCODE instruction, a user-programmable
identification code can be shifted out for examination. This
code is loaded into the USERCODE register during
programming of the Platform Flash PROM. If the device is
blank or was not loaded during programming, the
USERCODE register contains FFFFFFFFh.
Customer Code Register
For the XCFxxP Platform Flash PROM, in addition to the
USERCODE, a unique 32-byte Customer Code can be
assigned to each design revision enabled for the PROM.
The Customer Code is set during programming, and is
typically used to supply information about the design
revision contents. A private JTAG instruction is required to
read the Customer Code. If the PROM is blank, or the
Customer Code for the selected design revision was not
loaded during programming, or if the particular design
revision is erased, the Customer Code contains all ones.
Notes:
1.
The <v> in the IDCODE field represents the device’s revision
code (in hex) and can vary.
ISC Status
IR[3]
XCF01S
XCF02S
XCF04S
XCF08P
XCF16P
XCF32P
Device
IR[2]
0
DONE
IR[2]
IR[1:0]
0 1
IR[1:0]
0 1
IDCODE
<v>5044093
<v>5045093
<v>5046093
<v>5057093
<v>5058093
<v>5059093
(1)
(hex)
→ TDO
→ TDO
8