hip6301vcbza-t Intersil Corporation, hip6301vcbza-t Datasheet
hip6301vcbza-t
Related parts for hip6301vcbza-t
hip6301vcbza-t Summary of contents
Page 1
... Pb-Free Available (RoHS Compliant) Ordering Information PART NUMBER TEMP. ( HIP6301VCB HIP6301VCBZ (See Note) HIP6301VCBZA (See Note) HIP6302VCB HIP6302VCBZ (See Note) Add “-T” suffix for tape and reel. NOTE: Intersil Pb-free products employ special Pb-free material sets ...
Page 2
Pinouts HIP6301V (SOIC) TOP VIEW 1 VID4 2 VID3 3 VID2 4 VID1 5 VID0 6 COMP FS/DIS 9 GND 10 VSEN 2 HIP6301V, HIP6302V PGOOD 18 PWM4 17 ISEN4 16 ISEN1 15 ...
Page 3
HIP6301V Block Diagram VSEN + X 0.9 + X1.15 AND FAULT COMP VID0 VID1 DYNAMIC VID2 VID D/A VID3 VID4 FB 3 HIP6301V, HIP6302V HIP6301V, HIP6302V VCC PGOOD POWER-ON RESET (POR LATCH CLOCK AND S SAWTOOTH GENERATOR ...
Page 4
HIP6302V Block Diagram VSEN + X 0.9 + X1.15 AND FAULT COMP VID0 VID1 DYNAMIC VID2 VID D/A VID3 VID4 FB 4 HIP6301V, HIP6302V VCC PGOOD POWER-ON RESET (POR LATCH CLOCK AND S SAWTOOTH GENERATOR + ∑ ...
Page 5
HIP6301V and HIP6302V Functional Pin Descriptions HIP6301V PINOUT 1 20 VID4 2 19 VID3 3 18 VID2 4 17 VID1 5 16 VID0 6 15 COMP FS/DIS 9 12 GND 10 VSEN 11 VID4, VID3, ...
Page 6
Typical Application - HIP6301V Controller with HIP6601B Gate Drivers FB COMP VCC VSEN ISEN1 PWM1 PGOOD PWM2 VID4 VID3 ISEN2 MAIN VID2 CONTROL VID1 HIP6301V VID0 PWM3 ISEN3 FS/DIS PWM4 ISEN4 GND 6 HIP6301V, HIP6302V HIP6301V, HIP6302V +12V VCC BOOT ...
Page 7
Absolute Maximum Ratings Supply Voltage .+7V ...
Page 8
Electrical Specifications Operating Conditions: V PARAMETER Percent Overvoltage Hysteresis RIN FB ERROR AMPLIFIER CORRECTION - ∑ DAC PROGRAMMABLE REFERENCE + ∑ AVERAGE - + ∑ ∑ CORRECTION FIGURE 1. SIMPLIFIED BLOCK DIAGRAM OF ...
Page 9
... PWM channels to accurately share the load current for enhanced reliability. The HIP6601, HIP6602 or HIP6603 MOSFET driver interfaces with the HIP6301V. For more information, see the datasheets for the individual Intersil MOSFET drivers. The HIP6301V is capable of controlling PWM power channels ...
Page 10
For the first 32 PWM switching cycles, the DAC output remains inhibited and the PWM outputs remain three stated. From the 33rd cycle and for another, approximately 150 cycles the PWM output remains low, clamping the lower output MOSFETs to ...
Page 11
If a new VID code is detected during a DAC change and the DAC can continue toward the new VID ...
Page 12
At the end of the delay, PWM outputs are restarted and the soft-start ramp is initiated short is present at that time, the cycle is repeated. This is the hiccup mode. Figure 8 shows the supply shorted under ...
Page 13
RIN Cc RFB COMP FB SAWTOOTH ERROR GENERATOR AMPLIFIER CORRECTION - + + - DIFFERENCE REFERENCE DAC TO OTHER CHANNELS TO OVER + CURRENT - TRIP COMPARATOR FIGURE 9. SIMPLIFIED FUNCTIONAL BLOCK DIAGRAM SHOWING CURRENT AND VOLTAGE SAMPLING Current Sensing ...
Page 14
R increases the apparent V voltage with increasing load CORE current, causing the system to decrease V balance at the FB pin. This is the desired “droop” voltage used to maintain V within limits ...
Page 15
SAMPLE current ( ------- - + IN CORE ----------------------------------------------------------------------------------- - ( ) F ( SAMPLE 6L SW Where: ...
Page 16
Dedicate another solid layer as a power plane and break this plane into smaller islands of common voltage levels. Keep the metal runs from the PHASE terminal to inductor L short. The power plane should ...
Page 17
Small values of output inductance can cause excessive power dissipation. The HIP6301V and HIP6302V are designed for stable operation for ripple currents up to twice the load current. However, for this condition, the RMS current is 115% above the value ...
Page 18
MOSFET Selection and Considerations In high-current PWM applications, the MOSFET power dissipation, package selection and heatsink are the dominant design factors. The power dissipation includes two loss components; conduction loss and switching loss. These losses are distributed between the upper ...
Page 19
Small Outline Plastic Packages (SOIC) N INDEX 0.25(0.010) H AREA E - SEATING PLANE - -C- α µ 0.10(0.004) 0.25(0.010 NOTES: 1. Symbols are defined in ...
Page 20
... Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use ...