GCM32DR72A225KA64L Murata, GCM32DR72A225KA64L Datasheet - Page 17

• Manufacturer Part Number: GCM32DR72A225KA64L
• Description: Multilayer Ceramic Capacitors (MLCC) - SMD/SMT 1210 2.2uF 100volts X7R +/-10%
• Manufacturer: Murata
• Series: GCMr

Specifications of GCM32DR72A225KA64L

• Capacitance: 2.2 uF
• Tolerance: 10 %
• Voltage Rating: 100 Volts
• Operating Temperature Range: - 55 C to + 125 C
• Temperature Coefficient / Code: X7R
• Package / Case: 1210 (3225 metric)
• Product: Automotive MLCCs
• Dimensions: 2.5 mm W x 3.2 mm L x 2 mm H
• Dissipation Factor Df: 0.01
• Termination Style: SMD/SMT
• Lead Free Status / Rohs Status: Details

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
14
15
16
17
GCM Series Specification and Test Methods
Continued from the preceding page.
Thermal Shock
ESD
Solderability
Electrical
Characteri-
zation
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
AEC-Q200
Test Item
Appearance
Capacitance
Change
Q/D.F.
I.R.
Appearance
Capacitance
Change
Q/D.F.
I.R.
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
Temperature Compensating Type
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within ±2.5% or ±0.25pF
(Whichever is larger)
30pF min.: QU1000
30pF max.: QU400+20C
C: Nominal Capacitance (pF)
More than 10,000MΩ or 500Ω · F
(Whichever is smaller)
No marking defects
Within the specified tolerance
30pF min.: QU1000
30pF max.: QU400+20C
C: Nominal Capacitance (pF)
More than 10,000MΩ or 500Ω · F
(Whichever is smaller)
95% of the terminations is to be soldered evenly and
continuously.
No defects or abnormalities
Within the specified tolerance
30pF min.: QU1000
30pF max.: QU400+20C
C: Nominal Capacitance (pF)
25°C
More than 100,000MΩ or 1,000Ω · F
(Whichever is smaller)
Max. Operating Temperature···125°C
More than 10,000MΩ or 100Ω · F
(Whichever is smaller)
No failure
Specifications
Within ±10.0%
W.V.: 25Vmin.: 0.025 max.
W.V.: 16V: 0.035 max.
W.V.: 25Vmin.: 0.025 max.
W.V.: 16V: 0.035 max.
W.V.: 25V min.: 0.025 max.
W.V.: 16V: 0.035 max
25°C
More than 10,000MΩ or 500Ω · F
(Whichever is smaller)
Max. Operating Temperature···125°C
More than 1,000MΩ or 10Ω · F
(Whichever is smaller)
High Dielectric Type
*1
*1
*1
*1
*1
*1
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as (18). Perform the 300 cycles
according to the two heat treatments listed in the following table
(Maximum transfer time is 20 seconds). Let sit for 24±2 hours at
room temperature, then measure.
• Initial measurement for high dielectric constant type
Perform a heat treatment at 150
let sit for 24±2 hours at room temperature.
Perform the initial measurement.
Per AEC-Q200-004
(a) Preheat at 155°C for 4 hours. After preheating, immerse the
(b) Should be placed into steam aging for 8 hours±15 minutes.
(c) Should be placed into steam aging for 8 hours±15 minutes.
Visual inspection.
The capacitance/Q/D.F. should be measured at 25°C at the
frequency and voltage shown in the table.
(1) Temperature Compensating Type
(2) High Dielectric Type
The insulation resistance should be measured with a DC voltage
not exceeding the rated voltage at 25°C and 125°C and within 2
minutes of charging.
No failure should be observed when 250% of the rated voltage is
applied between the terminations for 1 to 5 seconds, provided the
charge/discharge current is less than 50mA.
Specifications and Test Methods
capacitor in a solution of ethanol (JIS-K-8101) and rosin (JIS-
K-5902) (25% rosin in weight proportion). Immerse in eutectic
solder solution for 5+0/-0.5 seconds at 235±5°C.
After preheating, immerse the capacitor in a solution of
ethanol (JIS-K-8101) and rosin (JIS-K-5902) (25% rosin in
weight proportion). Immerse in eutectic solder solution for
5+0/-0.5 seconds at 235±5°C.
After preheating, immerse the capacitor in a solution of
ethanol (JIS-K-8101) and rosin (JIS-K-5902) (25% rosin in
weight proportion). Immerse in eutectic solder solution for 120
±5 seconds at 260±5°C.
Time (min.)
Temp. (°C)
Step
Capacitance
Capacitance
C V 1000pF
C G 1000pF
C V 10µF
C G 10µF
-55+0/-3
AEC-Q200 Test Method
15 ± 3
1
Frequency
Frequency
1 ± 0.1MHz
120 ± 24Hz
1 ± 0.1kHz
1 ± 0.1kHz
Continued on the following page.
W0
Y10
125+3/-0 (5C, C7, R7)
°C for one hour and then
15 ± 3
2
0.5 to 5Vrms
0.5 ± 0.1Vrms
1 ± 0.2Vrms
1 ± 0.2Vrms
Voltage
Voltage
C03E.pdf
15
09.3.31
1