SC16C852LIB-F NXP Semiconductors, SC16C852LIB-F Datasheet - Page 10

• Manufacturer Part Number: SC16C852LIB-F
• Manufacturer: NXP Semiconductors

Specifications of SC16C852LIB-F

• Number Of Channels: 2
• Transmitter And Receiver Fifo Counter: Yes
• Data Rate: 5Mbps
• Package Type: LQFP
• Mounting: Surface Mount
• Pin Count: 48
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Lead Free Status / Rohs Status: Compliant

NXP Semiconductors
Table 2.
SC16C852L_3
Product data sheet
Symbol
RXA
RXB
RXRDYA
RXRDYB
TXA
TXB
TXRDYA
TXRDYB
V
V
XTAL1
XTAL2
DD
SS
Pin description
Pin
LQFP48
5
4
31
18
7
8
43
6
42
17
13
14
HVQFN32 TFBGA36
4
3
-
-
5
6
-
-
26
13
10
11
[1]
…continued
D1
C2
-
-
D2
E1
-
-
C4
D4
F2
E3
1.8 V dual UART with 128-byte FIFOs and IrDA encoder/decoder
Type
I
I
O
O
O
O
O
O
I
I
I
O
Rev. 03 — 18 January 2008
Description
Receive data A, B. These inputs are associated with individual
serial channel data to the SC16C852L receive input circuits, A
through B. The RX signal will be a logic 1 during reset, idle (no
data), or when not receiving data. During the local loopback mode,
the RXA/RXB input pin is disabled and TX data is connected to the
UART RX input, internally.
Receive Ready A, B (active LOW). This function provides the
RX FIFO/RHR status for individual receive channels (A to B).
RXRDY is primarily intended for monitoring DMA mode 1 transfers
for the receive data FIFOs. A logic 0 indicates there is a receive
data to read/upload, that is, receive ready status with one or more
RX characters available in the FIFO/RHR. This pin is a logic 1
when the FIFO/RHR is empty or when the programmed trigger
level has not been reached. This signal can also be used for single
mode transfers (DMA mode 0).
Transmit data A, B. These outputs are associated with individual
serial transmit channel data from the SC16C852L. The TX signal
will be a logic 1 during reset, idle (no data), or when the transmitter
is disabled. During the local loopback mode, the TXA/TXB output
pin is disabled and TX data is internally connected to the UART RX
input.
Transmit Ready A, B (active LOW). These outputs provide the
TX FIFO/THR status for individual transmit channels (A to B).
TXRDY is primarily intended for monitoring DMA mode 1 transfers
for the transmit data FIFOs. An individual channel’s TXRDYA,
TXRDYB buffer ready status is indicated by logic 0, that is, at lease
one location is empty and available in the FIFO or THR. This pin
goes to a logic 1 (DMA mode 1) when there are no more empty
locations in the FIFO or THR. This signal can also be used for
single mode transfers (DMA mode 0).
Power supply input.
Signal and power ground.
Crystal or external clock input. Functions as a crystal input or as
an external clock input. A crystal can be connected between this
pin and XTAL2 to form an internal oscillator circuit. Alternatively, an
external clock can be connected to this pin to provide custom data
rates (see
See
Output of the crystal oscillator or buffered clock. (See also
XTAL1.) Crystal oscillator output or buffered clock output. Should
be left open if an external clock is connected to XTAL1.
Figure
Section 6.9 “Programmable baud rate
8.
SC16C852L
© NXP B.V. 2008. All rights reserved.
generator”).
10 of 63