5962-9316603MXA Cypress Semiconductor Corp, 5962-9316603MXA Datasheet - Page 7

• Manufacturer Part Number: 5962-9316603MXA
• Manufacturer: Cypress Semiconductor Corp

Specifications of 5962-9316603MXA

• Lead Free Status / RoHS Status: Not Compliant

DSCC FORM 2234
APR 97
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this
drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and
herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
herein) involving devices acquired to this drawing is required for any change that affects this drawing.
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
microcircuit group number 42 (see MIL-PRF-38535, appendix A).
1/ These are absolute values with respect to device ground and all overshoots and undershoots due to system or tester
2/ For test purposes, not more than one output at a time should be shorted. Short circuit test duration should not exceed
3/ Tested initially and after any design or process changes that affect that parameter, and therefore shall be guaranteed to
4/ At f = f
5/ Devices 01-03 CE = 0.0 V, CS
6/ AC tests are performed with input rise and fall times of 5 ns or less, timing reference levels of 1.5 V, input pulse levels of 0
7/ Transition is measured at steady-state high level -500 mV or steady-state low level +500 mV on the output from the 1.5 V
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2
3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in
Chip enable active to power
up 3/
Chip enable inactive to
power down 3/
Output hold from address
change 3/
noise are included.
thirty seconds.
the limits specified in table I.
to 3.0 V, and the output load on figure 3, circuit A.
level on the input with the output load on figure 3, circuit B.
DEFENSE SUPPLY CENTER COLUMBUS
MAX
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43218-3990
, the inputs are switching at 1/t
Test
STANDARD
TABLE I. Electrical performance characteristics – Continued.
Symbol
t
t
t
PU
PD
OH
1
= 3.0 V, CS
AA
unless otherwise specified
.
-55°C ≤ T
4.5 V ≤ V
2
= 0.0 V; devices 04-06 CE = 0.0 V, OE = 3.0 V.
Conditions
C
CC
≤ +125°C
≤ 5.5 V
SIZE
A
Group A
subgroups
REVISION LEVEL
Device
type
01,04
02,05
03,06
ALL
ALL
B
Min
0
0
Limit
SHEET
Max
5962-93166
60
50
40
Unit
7