DLP-RF2 DLP Design Inc, DLP-RF2 Datasheet - Page 6

• Manufacturer Part Number: DLP-RF2
• Description: Zigbee / 802.15.4 Modules & Development Tools USE 626-DLP-RF2-Z
• Manufacturer: DLP Design Inc

Specifications of DLP-RF2

• Wireless Frequency: 2.4 GHz
• Interface Type: 2 Wire Serial
• Output Power: 1 mW
• For Use With/related Products: MC13193, MC9S08GT60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Rev 1.8 (November 2005)
0xCC
0xAC
0xAD
0xAE
0xCA
0xCB
0xAF
0xB6
0xB7
0xB8
0xB9
0xC0
0xC1
0xC2
0xC3
0xC4
0xC5
0xC6
0xC7
0xC8
0xC9
MC9S08GT60
MC9S08GT60
MC9S08GT60
MC9S08GT60
MC9S08GT60
MC9S08GT60
MC9S08GT60
MC9S08GT60
Serial / USB
Serial / USB
Serial / USB
Serial / USB
Serial / USB
Serial / USB
Serial / USB
Serial / USB
Serial / USB
Serial / USB
Serial / USB
Serial / USB
Serial / USB
Set/Clear I/O pin, 2 Data Bytes: Port: 0-8
(Port 8 is PTC0), State: 0/1
Setup A/D, 2 Data Bytes: Port: 0-6, Mode:
0=Off, 1=On
Read A/D, 1 Data Byte: Channel: 0-6
Read VBAT (no data)
Request Board Type (DLP-RF1, RF2-Z),
ROM and RFIC versions (no data)
Return Board ID (not available through RF
transceiver, physical connection only)
(destination ID ignored) (no data)
Pulse high/low with delay while high (For
DLP-RF2-ZRELAY Only; additional
hardware required) 2 Data Bytes: Relay
Number: 1/2, State: 0/1 (RST/SET)
Read Temperature and Humidity (DLP-
RF2-Z only; additional hardware required)
(no data) Refer to RFTestAp source code
for data processing details
Generic Reply or “ACK” for selected
non-broadcast commands
Check-in from DLP-RF2-Z due to monitored
port pin input change. 2 Data Bytes:
Current I/O pin state (A6, B6:0), Bit-field
with bits set for the port pins that changed
state (A6, B6:0)
Check-in from DLP-RF2-Z due to wake
from sleep (no data)
Measured energy data, 16 Data Bytes:
Channel 0 – channel 15 energy levels,
Refer to RFTestAp source code for data
processing details
EEPROM read reply, 1 Data Byte:
EEPROM Read data
Write EEPROM reply (no data)
Read I/O pin reply, 1 Data Byte: pin state
Set direction reply (no data)
Set/Clear I/O pin reply (no data)
Setup A/D reply (no data)
Read A/D reply, 2 Data Bytes: ATD1RH,
ATD1RL, voltage result =
((ATD1RH << 8) | ATD1RL) * Vref / 1024
Read VBAT reply, 2 Data Bytes: ATD1RH,
ATD1RL, Refer to RFTestAp source code
for data processing details
Read Temperature & Humidity reply, Refer
to RFTestAp source code for data
processing details
6
DLP-RF2-Z  DLP Design, Inc.
0xCA
0xCB
0xCD
0xCC
0xC8
0xC9
0xCF
0xC0