C500TS502 Omron, C500TS502 Datasheet - Page 8

• Manufacturer Part Number: C500TS502
• Description: RTD INPUT MODULE
• Manufacturer: Omron

Specifications of C500TS502

• Leaded Process Compatible: No
• Peak Reflow Compatible (260 C): No
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Default Settings
1- -1
1- -2
2
Terminology
Quick Start Procedure
The following terms are used throughout this manual. Review these terms as
necessary.
The following steps are used as a quick reference guide when installing and
setting up the module. For specific details, refer to the appropriate section.
1. Unpacking the module
2. Set rotary switches and jumpers
3. Replace the connector on the module
4. Install the module on the backplane
5. Wire the I/O terminal block
6. Record settings in the configuration worksheet
7. Power-up the module
8. Verify default ladder programs
9. Check module indicators
Note:
Caution:
DANGER!:
2 Word Mode
4 Word Mode
Data Memory
Bit
LSB
Jumper Pins
(8 sets of 8 pins)
Jumpers (16)
Rotary
switches (8)
2/4 Word Mode
Jumper
Captive
screws (2)
Terminal block
cover
Terminal
Connectors (32)
Word
Alerts the user about special features or procedures.
Indicates information that, if not heeded, could result
in minor injury or damage to the product.
Indicates information that, if not heeded, could result
in loss of life or serious injury.
Refers to the 2 word communication mode between
the I/O module and the PLC’s CPU. This mode
communicates with the CPU using two I/O words and
the intelligent read and write commands.
Refers to the 4 word communication mode between
the I/O module and the PLC’s CPU. This mode
communicates with the CPU using four I/O words and
standard I/O commands.
Refers to the 16 bit register memory in the PLC’s
CPU used to store and manipulate data.
Set by the user to enable a particular function.
0=OFF/DISABLE, 1=ON/ENABLE
Least significant bit.
Jumper pins consist of 8 pins per RTD input. There
are eight RTD inputs. Jumpers are installed on a pair
of pins to set a specific RTD type and wiring
configuration.
Jumpers are plastic devices. They are located under
the terminal block cover. Jumpers are used to
connect pairs of jumper pins for specific RTD type
and wiring configuration.
Rotary switches are located at the back of the
module and are used to set the type of RTD input.
Located behind the indicator cover, this jumper sets
the module to 2 or 4 word mode.
Spring-loaded screws which are retained in the
terminal block cover and used to secure this cover to
the module.
A plastic cover located at the front of the module
which is used to cover and protect the internal
components of the module.
A device used to clamp-down electrical wiring to the
module.
Indicates a memory location in the PLC data memory
or in the module memory map. A word can contain a
single piece of data or it can contain bits or flags for
each of 16 input points.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . .
Section 1- -2
Appendix D
Section 2
Section 3
Section 3
Section 3
Section 4
Section 2