A16-1NRN Omron, A16-1NRN Datasheet - Page 20

• Manufacturer Part Number: A16-1NRN
• Description: NEON LAMP 110V RED FOR A16
• Manufacturer: Omron
• Type: Neon Lamp, 110 VoltsACr
• Series: A16r

Specifications of A16-1NRN

• Accessory Type: Neon Lamp Replacement
• Supply Voltage: 110V
• Base Type: Bi-Pin
• Colour: Red
• Current Rating: 1.5mA
• Svhc: No SVHC (15-Dec-2010)
• Illumination Colour: Red
• Operating Lifetime: 10000h
• Voltage Rating Vac: 110V
• Average Bulb Life: 1000
• Color: Red
• Illumination: Illuminated
• Height: 13 mm
• Illumination Color: Red
• Mounting Style: Snap In
• Termination Style: Tabs
• Lamp Base Type: Bi-Pin
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: A16 Series
• For Use With: Z1397 - SWTCH KNOB RND 3POS DPDT ILL REDZ1394 - SWTCH KNOB RND 2POS SPDT ILL REDZ1391 - SWTCH KNOB RND 2POS SPDT ILL REDZ1385 - SWITCH KNB RECT 3POS DPDT ILLZ1382 - SWITCH KNB RECT 2POS SPDT ILLZ1379 - SWITCH KNB RECT 2POS SPDT ILLZ1373 - SWITCH KNOB SQ 3-POS DPDT ILLZ1370 - SWITCH KNOB SQ 2-POS SPDT ILLZ1367 - SWITCH KNOB SQ 2-POS SPDT ILLZ1309 - SWITCH PB RND MOM DPDT ILLUM REDZ1305 - SWITCH PB RECT MOM DPDT ILLUMZ1301 - SWITCH PB SQ MOM DPDT ILLUM RED
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: A161NRN; Z1342

Technical Information
•
•
•
•
18
Hand soldering
Automatic
soldering
Do not use soldering flux that contains chlorine. Doing so may
result in metal corrosion.
Perform hand soldering using the appropriate soldering iron.
With the exception of PCB-mounting Switches, when performing
hand soldering, hold the Switch so that the terminals point
downwards so that flux does not get inside the Switch.
Leave a gap of at least 1 mm between the soldered parts and the
surface of the case so that flux does not get inside the Switch.
Correct
Terminal
Method
Incorrect
Dip
soldering
Reflow
soldering
Incorrect
Lead wire
Perform soldering for be-
tween 3 to 5 s with a suit-
able soldering iron.
Large-
capacity
soldering
iron
Soldering iron
Jet soldering
bath
Dip soldering
bath
Infrared reflow
(IR) soldering
bath
Vapor-phase
(VPS) reflow
soldering bath
Soldering
device
Incorrect
Correct
Small-capacity
soldering iron
used for a long
time
Small quantities
Different
materials
Lead wire
terminals
Large quantities
of discrete
terminals
Large quantities
of miniature
SMD terminals
Application
•
•
When applying flux using a brush, use a sponge soaked in flux as
shown below. Do not apply more than is necessary. Also, apply
the flux with the PCB inclined at an angle of less than 80° so that
flux does not flow onto the mounting surface of the Switch.
Do not place PCBs that have had flux applied or have been
soldered on top of each other. Otherwise, the flux on the PCB’s
solder surface may stain the upper part of the Switch or even
permeate the inside of the Switch and cause contact failure.
Incorrect
Flux
Incorrect
Correct
Sponge
soaked in flux
Flux
Lead wire
Terminal
Case
Solder
Brush
Brush
Technical Information
Do not place PCBs
with solder or flux on
top of each other.
80°C
max.
1 mm min.