C8051F523A-IM Silicon Laboratories Inc, C8051F523A-IM Datasheet - Page 163

• Manufacturer Part Number: C8051F523A-IM
• Description: IC 8051 MCU 4K FLASH 10DFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F52xr

Specifications of C8051F523A-IM

• Program Memory Type: FLASH
• Program Memory Size: 4KB (4K x 8)
• Package / Case: 10-DFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 6
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.25 V
• Data Converters: A/D 6x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: C8051F5x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 3
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F500DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 6-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1488 - KIT DEV C8051F53XA, C8051F52XA770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1455 - ADAPTER PROGRAM TOOLSTICK F520
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1491-5

17. LIN (C8051F520/0A/3/3A/6/6A and C8051F530/0A/3/3A/6/6A)
Important Note: This chapter assumes an understanding of the Local Interconnect Network (LIN) proto-
col. For more information about the LIN protocol, including specifications, please refer to the LIN consor-
tium (http://www.lin-subbus.org/).
LIN is an asynchronous, serial communications interface used primarily in automotive networks. The Sili-
con Laboratories LIN controller is compliant to the 2.1 Specification, implements a complete hardware LIN
interface, and includes the following features:



Note: The minimum system clock (SYSCLK) required when using the LIN peripheral is 8 MHz.
The LIN peripheral has four main components:
Selectable Master and Slave modes.
Automatic baud rate option in slave mode
The internal oscillator is accurate to within 0.5% of 24.5 MHz across the entire temperature range and
for VDD voltages greater than or equal to the minimum output of the on-chip voltage regulator, so an
external oscillator is not necessary for master mode operation for most systems.
1. LIN Access Registers—Provide the interface between the MCU core and the LIN peripheral.
2. LIN Data Registers—Where transmitted and received message data bytes are stored.
3. LIN Control Registers—Control the functionality of the LIN interface.
4. Control State Machine and Bit Streaming Logic—Contains the hardware that serializes mes-
sages and controls the bus timing of the controller.
RX
TX
Indirectly Addressed Registers
Registers
LIN Data
Control State Machine
LIN Controller
Figure 17.1. LIN Block Diagram
C8051F520/0A/3/3A/6/6A and C8051F530/0A/3/3A/6/6A
C8051F52x/F52xA/F53x/F53xA
LIN Control
Registers
Rev. 1.3
8051 MCU Core
LINADDR
LINDATA
LINCF
163