PIC16C54-XT/P Microchip Technology, PIC16C54-XT/P Datasheet - Page 42

• Manufacturer Part Number: PIC16C54-XT/P
• Description: IC MCU OTP 512X12 18DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C54-XT/P

• Core Size: 8-Bit
• Program Memory Size: 768B (512 x 12)
• Core Processor: PIC
• Speed: 4MHz
• Peripherals: POR, WDT
• Number Of I /o: 12
• Program Memory Type: OTP
• Ram Size: 25 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 6.25 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 18-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16C
• No. Of I/o's: 12
• Ram Memory Size: 25Byte
• Cpu Speed: 4MHz
• No. Of Timers: 1
• Package: 18PDIP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 4 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Core: PIC
• Processor Series: PIC16C
• Maximum Clock Frequency: 40 MHz
• Data Ram Size: 25 B
• Data Rom Size: 512 B
• Mounting Style: Through Hole
• Height: 3.3 mm
• Length: 22.86 mm
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Supply Voltage (max): 6.25 V
• Supply Voltage (min): 3 V
• Width: 6.35 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

PIC16C5X
7.9
A device may be powered down (SLEEP) and later
powered up (Wake-up from SLEEP).
7.9.1
The Power-Down mode is entered by executing a
SLEEP instruction.
If enabled, the Watchdog Timer will be cleared but
keeps running, the TO bit (STATUS<4>) is set, the PD
bit (STATUS<3>) is cleared and the oscillator driver is
turned off. The I/O ports maintain the status they had
before the SLEEP instruction was executed (driving
high, driving low, or hi-impedance).
It should be noted that a RESET generated by a WDT
time-out does not drive the MCLR/V
For lowest current consumption while powered down,
the T0CKI input should be at V
MCLR/V
7.9.2
The device can wake up from SLEEP through one of
the following events:
1.
2.
Both of these events cause a device reset. The TO and
PD bits can be used to determine the cause of device
reset.
occurred (and caused wake-up). The PD bit, which is
set on power-up, is cleared when SLEEP is invoked.
The WDT is cleared when the device wakes from
sleep, regardless of the wake-up source.
DS30453B-page 42
An external reset input on MCLR/V
A Watchdog Timer time-out reset (if WDT was
enabled).
PP
Power-Down Mode (SLEEP)
SLEEP
WAKE-UP FROM SLEEP
The TO bit is cleared if a WDT time-out
pin must be at a logic high level.
DD
PP
or V
pin low.
PP
SS
pin.
and the
Preliminary
7.10
If
programmed, the on-chip program memory can be
read out for verification purposes.
7.11
Four memory locations are designated as ID locations
where the user can store checksum or other
code-identification numbers. These locations are not
accessible during normal execution but are readable
and writable during program/verify.
Use only the lower 4 bits of the ID locations and
always program the upper 8 bits as '1's.
Note:
Note:
the
Program Verification/Code Protection
ID Locations (not implemented on
PIC16C52)
code
Microchip does not recommend code pro-
tecting windowed devices.
Microchip will assign a unique pattern
number for QTP and SQTP requests and
for ROM devices. This pattern number will
be unique and traceable to the submitted
code.
protection
1998 Microchip Technology Inc.
bit(s)
have
not
been