PIC16C54-XT/P Microchip Technology, PIC16C54-XT/P Datasheet - Page 27

• Manufacturer Part Number: PIC16C54-XT/P
• Description: IC MCU OTP 512X12 18DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C54-XT/P

• Core Size: 8-Bit
• Program Memory Size: 768B (512 x 12)
• Core Processor: PIC
• Speed: 4MHz
• Peripherals: POR, WDT
• Number Of I /o: 12
• Program Memory Type: OTP
• Ram Size: 25 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 6.25 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 18-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16C
• No. Of I/o's: 12
• Ram Memory Size: 25Byte
• Cpu Speed: 4MHz
• No. Of Timers: 1
• Package: 18PDIP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 4 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Core: PIC
• Processor Series: PIC16C
• Maximum Clock Frequency: 40 MHz
• Data Ram Size: 25 B
• Data Rom Size: 512 B
• Mounting Style: Through Hole
• Height: 3.3 mm
• Length: 22.86 mm
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Supply Voltage (max): 6.25 V
• Supply Voltage (min): 3 V
• Width: 6.35 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

6.0
The Timer0 module has the following features:
• 8-bit timer/counter register, TMR0
• 8-bit software programmable prescaler
• Internal or external clock select
Figure 6-1 is a simplified block diagram of the Timer0
module, while Figure 6-2 shows the electrical structure
of the Timer0 input.
Timer mode is selected by clearing the T0CS bit
(OPTION<5>). In timer mode, the Timer0 module will
increment every instruction cycle (without prescaler). If
TMR0 register is written, the increment is inhibited for
the following two cycles (Figure 6-3 and Figure 6-4).
The user can work around this by writing an adjusted
value to the TMR0 register.
FIGURE 6-1:
FIGURE 6-2:
1998 Microchip Technology Inc.
- Readable and writable
- Edge select for external clock
TIMER0 MODULE AND
TMR0 REGISTER
T0CKI
Note 1: Bits T0CS, T0SE, PSA, PS2, PS1 and PS0 are located in the OPTION register.
pin
2: The prescaler is shared with the Watchdog Timer (Figure 6-6).
TIMER0 BLOCK DIAGRAM
ELECTRICAL STRUCTURE OF T0CKI PIN
T0SE
F
(1)
OSC
/4
T0CKI
T0CS
pin
Note 1: ESD protection circuits
0
1
(1)
V
SS
PS2, PS1, PS0
(1)
Programmable
Prescaler
Preliminary
V
SS
3
N
(2)
(1)
(1)
R
IN
Counter mode is selected by setting the T0CS bit
(OPTION<5>). In this mode, Timer0 will increment
either on every rising or falling edge of pin T0CKI. The
incrementing edge is determined by the source edge
select bit T0SE (OPTION<4>). Clearing the T0SE bit
selects the rising edge. Restrictions on the external
clock input are discussed in detail in Section 6.1.
The prescaler may be used by either the Timer0
module or the Watchdog Timer, but not both. The
prescaler assignment is controlled in software by the
control bit PSA (OPTION<3>). Clearing the PSA bit
will assign the prescaler to Timer0. The prescaler is
not readable or writable. When the prescaler is
assigned to the Timer0 module, prescale values of 1:2,
1:4,..., 1:256 are selectable. Section 6.2 details the
operation of the prescaler.
A summary of registers associated with the Timer0
module is found in Table 6-1.
PSA
1
0
(1)
PSout
Schmitt Trigger
Input Buffer
(2 cycle delay)
Sync with
Internal
Clocks
PSout
Sync
PIC16C5X
TMR0 reg
Data bus
DS30453B-page 27
8