LTC2401 Linear Technology, LTC2401 Datasheet
LTC2401
Available stocks
Related parts for LTC2401
LTC2401 Summary of contents
Page 1
... This eliminates the latency found in conven- tional converters and simplifies multiplexed applica- tions. Through a single pin, the LTC2401/LTC2402 can be configured for better than 110dB rejection at 50Hz or 60Hz 2%, or can be driven by an external oscillator for a user defined rejection frequency in the range 1Hz to 120Hz ...
Page 2
... Power Supply Rejection, 60Hz 2% FS SET Power Supply Rejection, 50Hz 2% FS SET 2 U RATINGS (Notes 1, 2) Operating Temperature Range + 0.3V) LTC2401/LTC2402C ................................ LTC2401/LTC2402I ............................ – 0.3V 0.3V) Storage Temperature Range ................. – 150 C CC Lead Temperature (Soldering, 10 sec).................. 300 C + 0.3V LTC2401CMS V 1 ...
Page 3
... – 800 A (Note 10 1.6mA (Note 10) O The denotes specifications which apply over the full operating temperature range, CONDITIONS (Note 12 (Note 12) CC LTC2401/LTC2402 MIN TYP MAX UNITS – 0.125 • V 1.125 • V REF REF 0 SET – ...
Page 4
... LTC2401/LTC2402 CHARACTERISTICS range, otherwise specifications are at T SYMBOL PARAMETER f External Oscillator Frequency Range EOSC t External Oscillator High Period HEO t External Oscillator Low Period LEO t Conversion Time CONV f Internal SCK Frequency ISCK D Internal SCK Duty Cycle ISCK f External SCK Frequency Range ...
Page 5
... REF absolute maximum rating of – 0. sions are performed alternately between CH0 and CH1 for the LTC2402. Pin Connect (NC) on the LTC2401. ZS (Pin 5): Zero-Scale Set Input. This pin defines the SET zero-scale input value. When V ...
Page 6
... U APPLICATIO S I FOR ATIO Output Data Format The LTC2401/LTC2402 serial output data stream is 32 bits long. The first 4 bits represent status information indicat- ing the sign, selected channel, input range and conversion state. The next 24 bits are the conversion result, MSB first. ...
Page 7
... R as shown in Figure 2. The voltage drop across these parasitic resistors leads to systematic offset and full-scale errors. In order to eliminate the errors associated with these parasitic resistors, the LTC2401/LTC2402 include a full- scale set input (FS ( shown in Figure 3, the FS SET ...
Page 8
... and V . The wide dynamic input SET SET IN range (– 300mV to 5.3V) and low noise (0.6ppm RMS) enable the LTC2401 or the LTC2402 to directly digitize the output of the bridge sensor ...
Page 9
... LTC2402. Direct Connection to a Full Bridge The LTC2402 interfaces directly 6-wire bridge, as shown in Figure 7. Like the LTC2401, the LTC2402 in- cludes a FS voltage directly across the bridge. This eliminates errors due to excitation currents flowing through parasitic resis- tors ...
Page 10
... LTC2401/LTC2402 U U APPLICATIO S I FOR ATIO The LTC2402’s single ended rejection of line frequencies ( 2%) and harmonics is better than 110dB. Since the device performs two independent single ended conver- sions each with > 110dB rejection, the overall common mode and differential rejection is much better than the 80dB rejection typically found in other differential input delta-sigma converters ...
Page 11
... TANT 2 ST2 V A CC2 B LTC1535 LOGIC COMMON FLOATING COMMON 2 BARRIER T1 = COILTRONICS CTX02-14659 OR SIEMENS B78304-A1477-A3 LTC2401/LTC2402 pull-down to until the LT1761’s CC1 10V TANT 10 F CERAMIC 2 LTC2402 SCK FS SET SDO CH1 CS CH0 GND ...
Page 12
... LTC2401/LTC2402 U W PACKAGE I FOR ATIO 0.007 (0.18) * DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE ** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE ...