EVAL-AD7476ACB Analog Devices Inc, EVAL-AD7476ACB Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
EVAL-AD7476ACB
Manufacturer Part Number
EVAL-AD7476ACB
Description
BOARD EVAL FOR AD7476A
Manufacturer
Analog Devices Inc
Datasheet
1.EVAL-AD7476ACB.pdf
(28 pages)
Specifications of EVAL-AD7476ACB
Rohs Status
RoHS non-compliant
Number Of Adc's
1
Number Of Bits
12
Sampling Rate (per Second)
1M
Data Interface
Serial
Inputs Per Adc
1 Differential
Input Range
0 ~ 5.25 V
Power (typ) @ Conditions
17.5mW @ 1MSPS, 5 V
Voltage Supply Source
Single
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
AD7476A
Lead Free Status / Rohs Status
Not Compliant
AD7476A/AD7477A/AD7478A
TYPICAL CONNECTION DIAGRAM
Figure 18 shows a typical connection diagram for the AD7476A/
AD7477A/AD7478A. V
such, V
input range of 0 V to V
16-bit word with four leading zeros followed by the MSB of the
12-bit, 10-bit, or 8-bit result. The 10-bit result from the AD7477A
is followed by two trailing zeros, and the 8-bit result from the
AD7478A is followed by four trailing zeros. Alternatively, because
the supply current required by the AD7476A/AD7477A/AD7478A
is so low, a precision reference can be used as the supply source
to the AD7476A/AD7477A/AD7478A. A REF19x voltage refer-
ence
the required voltage to the ADC (see Figure 18). This configuration
is especially useful if the power supply is quite noisy, or if the
system supply voltages are at some value other than 5 V or 3 V
(for example, 15 V).
The REF19x outputs a steady voltage to the AD7476A/
AD7477A/AD7478A. If the low dropout REF193 is used, the
current it needs to supply to the AD7476A/AD7477A/ AD7478A is
typically 1.2 mA. When the ADC is converting at a rate of 1
MSPS, the REF193 needs to supply a maximum of 1.7 mA to the
AD7476A/AD7477A/AD7478A. The load regulation of the
REF193 is typically 10 ppm/mA (V
of 17 ppm (51 μV) for the 1.7 mA drawn from it. This corresponds
to a 0.069 LSB error for the AD7476A with V
REF193, a 0.017 LSB error for the AD7477A, and a 0.0043 LSB
error for the AD7478A.
For applications where power consumption is a concern, use the
power-down mode of the ADC and the sleep mode of the
REF19x reference to improve power performance. See the
Modes of Operation section.
680nF
0V TO V
INPUT
(REF195
DD
1.2mA
DD
should be well decoupled. This provides an analog
V
GND
V
IN
Figure 18. REF193 as Power Supply to AD7476A/
DD
0.1μF
for 5 V or
AD7476A/
AD7477A/
AD7478A
TANT
1μF
DD
3V
AD7477A/AD7478A
REF
REF193
. The conversion result is output in a
SDATA
is taken internally from V
SCLK
CS
REF193
for 3 V) can be used to supply
S
= 5 V), resulting in an error
10μF
INTERFACE
SERIAL
0.1μF
DD
= 3 V from the
DD
5V
SUPPLY
μC/μP
and, as
Rev. E | Page 16 of 28
Table 7 provides typical performance data with various
references used as a V
room temperature under the same setup conditions.
Table 7. AD7476A Typical Performance for Various Voltage
References
Reference Tied to V
AD780
REF193
AD780
REF192
REF43
ANALOG INPUT
Figure 19 shows an equivalent circuit of the analog input
structure of the AD7476A/AD7477A/AD7478A. The two
diodes, D1 and D2, provide ESD protection for the analog
input. Care must be taken to ensure that the analog input signal
never exceeds the supply rails by more than 300 mV. This
causes the diodes to become forward-biased and start
conducting current into the substrate. The maximum current
these diodes can conduct without causing irreversible damage
to the part is 10 mA. The Capacitor C1 in Figure 19 is typically
about 6 pF and can primarily be attributed to pin capacitance.
The Resistor R1 is a lumped component made up of the on
resistance of a switch. This resistor is typically about 100 Ω. The
Capacitor C2 is the ADC sampling capacitor and has a
capacitance of 20 pF typically.
For ac applications, removing high frequency components from
the analog input signal is recommended by use of a band-pass
filter on the relevant analog input pin. In applications where
harmonic distortion and signal-to-noise ratio are critical, drive
the analog input from a low impedance source. Large source
impedances significantly affect the ac performance of the ADC,
necessitating the use of an input buffer amplifier. The choice of
the op amp is a function of the particular application.
@ 3 V
@ 2.5 V
V
IN
6pF
C1
Figure 19. Equivalent Analog Input Circuit
DD
V
CONVERSION PHASE – SWITCH OPEN
TRACK PHASE – SWITCH CLOSED
DD
DD
D1
D2
source for a 100 kHz input tone at
AD7476A SNR Performance (dB)
72.65
72.35
72.5
72.2
72.6
R1
20pF
C2