DEMO9S08EL32AUTO Freescale Semiconductor, DEMO9S08EL32AUTO Datasheet - Page 34
![DEMO BOARD EL32 AUTO](/photos/37/58/375858/demo9s08sg32bd_sml.jpg)
DEMO9S08EL32AUTO
Manufacturer Part Number
DEMO9S08EL32AUTO
Description
DEMO BOARD EL32 AUTO
Manufacturer
Freescale Semiconductor
Type
MCUr
Datasheets
1.DEMO9S08EL32.pdf
(356 pages)
2.DEMO9S08EL32.pdf
(14 pages)
3.DEMO9S08EL32.pdf
(2 pages)
Specifications of DEMO9S08EL32AUTO
Contents
Board, Cable, CD and Documentation
Processor To Be Evaluated
MC9S08EL32
Data Bus Width
8 bit
Interface Type
RS-232, USB
Operating Supply Voltage
12 V
For Use With/related Products
MC9S08EL32
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 34 of 356
- Download datasheet (9Mb)
Chapter 3 Modes of Operation
Most background commands are not available in stop mode. The memory-access-with-status commands
do not allow memory access, but they report an error indicating that the MCU is in either stop or wait
mode. The BACKGROUND command can be used to wake the MCU from stop and enter active
background mode if the ENBDM bit is set. After entering background debug mode, all background
commands are available.
3.7
Stop2 mode is entered by executing a STOP instruction under the conditions as shown in
of the internal circuitry of the MCU is powered off in stop2 with the exception of the RAM. Upon entering
stop2, all I/O pin control signals are latched so that the pins retain their states during stop2.
Exit from stop2 is performed by asserting RESET on the MCU. In addition, the real-time counter (RTC)
can wake the MCU from stop2, if enabled.
Upon wake-up from stop2 mode, the MCU starts up as from a power-on reset (POR):
In addition to the above, upon waking up from stop2, the PPDF bit in SPMSC2 is set. This flag is used to
direct user code to go to a stop2 recovery routine. PPDF remains set and the I/O pin states remain latched
until a 1 is written to PPDACK in SPMSC2.
To maintain I/O states for pins that were configured as general-purpose I/O before entering stop2, the user
must restore the contents of the I/O port registers, which have been saved in RAM, to the port registers
before writing to the PPDACK bit. If the port registers are not restored from RAM before writing to
PPDACK, then the pins will switch to their reset states when PPDACK is written.
For pins that were configured as peripheral I/O, the user must reconfigure the peripheral module that
interfaces to the pin before writing to the PPDACK bit. If the peripheral module is not enabled before
writing to PPDACK, the pins will be controlled by their associated port control registers when the I/O
latches are opened.
3.8
When the MCU enters any stop mode, system clocks to the internal peripheral modules are stopped. Even
in the exception case (ENBDM = 1), where clocks to the background debug logic continue to operate,
clocks to the peripheral systems are halted to reduce power consumption. Refer to
Mode” and
34
•
•
•
All module control and status registers are reset
The LVD reset function is enabled and the MCU remains in the reset state if V
trip point (low trip point selected due to POR)
The CPU takes the reset vector
Stop2 Mode
On-Chip Peripheral Modules in Stop Modes
Section 3.6.1, “Stop3 Mode
MC9S08EL32 Series and MC9S08SL16 Series Data Sheet, Rev. 3
” for specific information on system behavior in stop modes.
Section 3.7, “Stop2
Freescale Semiconductor
DD
is below the LVD
Table
3-1. Most
Related parts for DEMO9S08EL32AUTO
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![MC14560BCP](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
![MC12034AP](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
![MPIC2112P](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
![MC14520BCP](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
![MC12026AP](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
![MC145152P2](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
![MC68HC11A0P](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
![MCM6726DWJ10](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
![MC44355](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
![MC13282AP](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
![MC14519BCP](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
![MC14495P1](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
![SN74LS796N](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
![MC142100CP](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet:
![MC34014P](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet: