101-1017 Rabbit Semiconductor, 101-1017 Datasheet - Page 20
101-1017
Manufacturer Part Number
101-1017
Description
KIT DEV POWERCORE 3800 INT'L
Manufacturer
Rabbit Semiconductor
Series
PowerCore FLEXr
Type
MPU Moduler
Datasheet
1.101-1007.pdf
(240 pages)
Specifications of 101-1017
Contents
RabbitCore Module, Dev. Board, AC Adapter, Cable and Dynamic C® CD-Rom
Processor To Be Evaluated
PowerCore 38xx
Interface Type
Ethernet
For Use With/related Products
RCM3800
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 20 of 240
- Download datasheet (3Mb)
2.2.3 Connect Power
When all other connections have been made, you can connect power to the PowerCore
module. In most cases where a locking power connector is stuffed at J3, connect the lock-
ing plug from the wall transformer to the J3 locking connector on the PowerCore module,
taking care to line up the polarized tab on the locking plug with the locking connector as
shown in Figure 3.
Plug in the wall transformer.
Board located near the RESET button should light up
Prototyping Board are now ready to be used.
If you selected one of the FLEX configuration options (Options 1 and 2 in Appendix D.1.1)
for regulated or unregulated DC power supplied from outside the PowerCore module, no
locking connector is stuffed at J3 on the PowerCore module. Instead, either regulated +5 V
DC is supplied to the PowerCore from your motherboard via pins 5 and 6 of header J4, or
unregulated DC power is supplied via pins 1 and 5 of header J4, depending on which
option you selected. The voltage range for unregulated DC power is established by your
selection of a voltage regulator in Option 2 as explained in Appendix D.1.1.
12
NOTE: This provision of external DC power is not possible when you are using the
NOTE: The RESET button is provided on the Prototyping Board to allow a hardware
PowerCore Prototyping Board, which has no provision to supply powerto the Power-
Core module. Any external DC power must come from a motherboard of your own
design for use with one of these FLEX options.
reset without disconnecting power.
CAUTION: It is important that power is connected in the order specified in these
instructions—connect the locking plug from the wall transformer to the J3 locking
connector on the PowerCore module before you plug in the wall transformer. This is
important for your safety because of the high AC voltages present and to avoid possi-
ble damage to your PowerCore module.
CAUTION: The heat sinks on the PowerCore module can become very hot. Avoid
any contact with them.
The DS3 and DS4 yellow and green LEDs on the Prototyping
. The PowerCore module and the
PowerCore FLEX
Related parts for 101-1017
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT DEV STANDARD RCM5700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
BL4S200 TOOL KIT
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEV FOR BL2500 COYOTE
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
Microcontroller Modules & Accessories Keypad/Display Unit 5V Panel Mount
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
Single Board Computers 24VDC/110 Power Supp
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE RABBITCORE RCM3720
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3220
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3210
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD OP6600 W/SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BD BL2000 SRAM/FLSH
Manufacturer:
Rabbit Semiconductor