101-1017 Rabbit Semiconductor, 101-1017 Datasheet - Page 17
101-1017
Manufacturer Part Number
101-1017
Description
KIT DEV POWERCORE 3800 INT'L
Manufacturer
Rabbit Semiconductor
Series
PowerCore FLEXr
Type
MPU Moduler
Datasheet
1.101-1007.pdf
(240 pages)
Specifications of 101-1017
Contents
RabbitCore Module, Dev. Board, AC Adapter, Cable and Dynamic C® CD-Rom
Processor To Be Evaluated
PowerCore 38xx
Interface Type
Ethernet
For Use With/related Products
RCM3800
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 17 of 240
- Download datasheet (3Mb)
2.1 Install Dynamic C
To develop and debug programs for PowerCore FLEX modules (and for all other and
Rabbit Semiconductor hardware), you must install and use Dynamic C.
If you have not yet installed Dynamic C version 9.20 (or a later version), do so now by
inserting the Dynamic C CD from the Tool Kit in your PC’s CD-ROM drive. If autorun is
enabled, the CD installation will begin automatically.
If autorun is disabled or the installation otherwise does not start, use the Windows
Start | Run
of the CD-ROM.
The installation program will guide you through the installation process. Most steps of the
process are self-explanatory.
Dynamic C uses a COM (serial) port to communicate with the target development system.
The installation allows you to choose the COM port that will be used. The default selec-
tion is COM1. You may select any available port for Dynamic C’s use. If you are not cer-
tain which port is available, select COM1. This selection can be changed later within
Dynamic C.
Once your installation is complete, you will have up to three new icons on your PC desk-
top. One icon is for Dynamic C, one opens the documentation menu, and the third is for
the Rabbit Field Utility, a tool used to download precompiled software to a target system.
If you have purchased any of the optional Dynamic C modules, install them after installing
Dynamic C. The modules may be installed in any order. You must install the modules in
the same directory where Dynamic C was installed.
User’s Manual
This chapter explains how to set up and use a PowerCore module
with a PowerCore Prototyping Board.
NOTE: It is assumed that you have a Tool Kit. If you purchased a PowerCore FLEX
NOTE: The installation utility does not check the selected COM port in any way. Speci-
module by itself, you will have to adapt the information in this chapter and elsewhere to
your test and development setup.
fying a port in use by another device (mouse, modem, etc.) may lead to a message such
as
menu or Windows Disk Explorer to launch
"could not open serial port"
2. G
when Dynamic C is started.
ETTING
setup.exe
from the root folder
S
TARTED
9
Related parts for 101-1017
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT DEV STANDARD RCM5700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
BL4S200 TOOL KIT
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEV FOR BL2500 COYOTE
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
Microcontroller Modules & Accessories Keypad/Display Unit 5V Panel Mount
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
Single Board Computers 24VDC/110 Power Supp
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE RABBITCORE RCM3720
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3220
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3210
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD OP6600 W/SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BD BL2000 SRAM/FLSH
Manufacturer:
Rabbit Semiconductor