M5211DEMO Freescale Semiconductor, M5211DEMO Datasheet
M5211DEMO
Specifications of M5211DEMO
Related parts for M5211DEMO
M5211DEMO Summary of contents
Page 1
... Freescale Semiconductor Demonstration Board for Freescale MCF5211 1 Overview The M5211DEMO is a low-cost development system for the Freescale MCF5211 ColdFire® microcontroller. Application development is quick and easy with the included DB9 serial cable and integrated BDM. The integrated BDM is compatible with popular hosting software and allows easy application development and debugging ...
Page 2
... Four GPT timers — BDM / JTAG port — 3.3 V operation — 66 MHz bus • 40 pin I/O port • Integrated USB BDM port • BDM / JTAG port, 26 pins, development port (not installed) Demonstration Board for Freescale MCF5211, Rev Figure 1. M5211DEMO Board Freescale Semiconductor ...
Page 3
... Supplied with DB9 serial cable, USB cable, utility / support CD • Manuals and wall adapter power supply. 1.2 Specifications • Board size: 3.5" x 5.5" • Power input +20 VDC, 9 VDC typical • Current consumption: 100 mA typical at 9 VDC input Demonstration Board for Freescale MCF5211, Rev. 1 Freescale Semiconductor Overview 3 ...
Page 4
... EMC Information on the M5211DEMO board This product is shipped from the factory with associated power supplies and cables, and has been verified to meet with requirements FCC as a CLASS A product. ...
Page 5
... RUN Mode RUN mode allows your application to execute out of flash memory when power is applied to the board or the RESET button is pressed. Use these settings to configure the M5211DEMO board for RUN mode using the USB bus to power the board. See alternate power input. ...
Page 6
... Demonstration Board for Freescale MCF5211, Rev Table 2. Run Mode Setup PWR_SEL Set to VB BDM_EN OFF COM_EN ALL ON (if required) VX_EN ON (if required) Table 3. Table 3. Debug Mode Setup PWR_SEL Set to VB BDM_EN ON COM_EN ALL ON (if required) VX_EN ON (if required) Section 7, “Power,” for details Freescale Semiconductor ...
Page 7
... Integrated BDM_PORT The M5211DEMO board features an integrated USB-BDM debugger from P&E Microcomputer Systems. The integrated debugger supports application development and debugging via the background debug mode. A USB, type B, connector provides connectivity between the target board to the host PC. The integrated debugger provides power and ground to the target, thereby eliminating the need to power the board externally ...
Page 8
... Note: This header is not installed in default configuration. 7 Power The M5211DEMO is designed to be powered from the USB_BDM during application development. A 2.0 mm barrel connector and a two-position, screw-type, terminal block (BATT) has been applied to support stand-alone operation. Additionally, the board may be powered through connector J1. The board may also be configured to supply power through connector J1 to external circuitry ...
Page 9
... The VDD LED is located after the OFF/ON switch and will indicate the state of the switch if the board is powered from the on-board regulator, the USB circuit, or the BATT terminal block input. Demonstration Board for Freescale MCF5211, Rev. 1 Freescale Semiconductor Figure 3, consists of a 2.1 mm, center-positive, barrel connector. Voltage 2.0 mm– ...
Page 10
... CONFIGURATION OFF—Input power source disconnected from upper voltage rail ON—Input power source connected to upper voltage rail Figure 5. OFF/ON Switch Select power input from USB-BDM Select power input from VR1 Figure 6. PWR_SEL Option Header CAUTION Freescale Semiconductor ...
Page 11
... The RESET switch provides a method to apply an asynchronous reset to the MCU and is connected directly to the RSTI* input on the MCU. Pressing the RESET switch forces the MCU into reset until the Demonstration Board for Freescale MCF5211, Rev. 1 Freescale Semiconductor Enable power connection to connector J1 Disable power connection to connector J1 Figure 7 ...
Page 12
... Timing Timing for the M5211DEMO is provided by an on-chip, 8 MHz relaxation oscillator in default configuration. Resistor R23 causes the MCU to select the internal oscillator as the timing source out of reset. Refer to the M5213 Integrated Microcontroller Reference Manual for details on use and configuration of internal timing ...
Page 13
... Communications The M5211DEMO board provides two Serial Communications Interface (SCI) ports, one Serial Peripheral Interface (SPI) port, and one Inter-Integrated Controller (IIC) port. RS-232 communications are supported through a DB9 connector and connector J1. SPI and IIC communications are supported through connector J1. The COM_EN option header enables SCI0 operation on the board. ...
Page 14
... IIC signaling connects directly between connector J1 and the MCU. Refer to the MCF5213 Integrated Microcontroller Reference Manual for details on using the IIC interface. 12 User Options The M5211DEMO includes various input and output devices to aid application development. User I/O devices include two momentary pushbutton switches, four green LEDs, and one potentiometer. 12.1 Pushbutton Switches Two pushbutton switches provide momentary, active-low input, for user applications ...
Page 15
... Option SW1 SW2 LED1 LED2 LED3 LED4 RV1 Demonstration Board for Freescale MCF5211, Rev. 1 Freescale Semiconductor Figure 12. User POT enabled User POT disabled Figure 12. POT_EN Option Header Table 4. User Option Connections MCU Port IRQ4 IRQ7 ...
Page 16
... I/O Port Connector 13 I/O Port Connector Connector J1 provides access to M5211DEMO I/O signals. Signal positions not shown are not connected (NC). Revision (Date) A (01/2006) Initial release as Axiom Manufacturing document. 1 (04/2007) • Converted document to Freescale identity and standards. • Formatting, layout, spelling, and grammar corrections. ...
Page 17
... THIS PAGE IS INTENTIONALLY BLANK Demonstration Board for Freescale MCF5211, Rev. 1 Freescale Semiconductor 17 ...
Page 18
... P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com Document Number: M5211DEMO Rev. 1 04/2007 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document ...