PIC16F690DM-PCTLHS Microchip Technology, PIC16F690DM-PCTLHS Datasheet - Page 90

• Manufacturer Part Number: PIC16F690DM-PCTLHS
• Description: BOARD DEMO PICTAIL HUMIDITY SNSR
• Manufacturer: Microchip Technology
• Series: PICtail™r

Specifications of PIC16F690DM-PCTLHS

• Sensor Type: Humidity
• Sensing Range: 1 ~ 99% RH
• Interface: Analog
• Voltage - Supply: 5V
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: MCP6291, PIC16F690
• Processor To Be Evaluated: MCP6291 and PIC16F690
• Interface Type: ICSP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162061 - HEADER INTRFC MPLAB ICD2 20PIN
• Sensitivity: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC16F631/677/685/687/689/690
6.12
The Timer1 Control register (T1CON), shown in
Register 6-1, is used to control Timer1 and select the
various features of the Timer1 module.
REGISTER 6-1:
DS41262E-page 88
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5-4
bit 3
bit 2
bit 1
bit 0
Note 1:
T1GINV
R/W-0
2:
Timer1 Control Register
(1)
T1GINV bit inverts the Timer1 gate logic, regardless of source.
TMR1GE bit must be set to use either T1G pin or C2OUT, as selected by the T1GSS bit of the CM2CON1
register, as a Timer1 gate source.
T1GINV: Timer1 Gate Invert bit
1 = Timer1 gate is active high (Timer1 counts when Timer1 gate signal is high)
0 = Timer1 gate is active low (Timer1 counts when gate is low)
TMR1GE: Timer1 Gate Enable bit
If TMR1ON = 0:
This bit is ignored
If TMR1ON = 1:
1 = Timer1 counting is controlled by the Timer1 Gate function
0 = Timer1 is always counting
T1CKPS<1:0>: Timer1 Input Clock Prescale Select bits
11 = 1:8 Prescale Value
10 = 1:4 Prescale Value
01 = 1:2 Prescale Value
00 = 1:1 Prescale Value
T1OSCEN: LP Oscillator Enable Control bit
If INTOSC without CLKOUT oscillator is active:
1 = LP oscillator is enabled for Timer1 clock
0 = LP oscillator is off
Else:
This bit is ignored
T1SYNC: Timer1 External Clock Input Synchronization Control bit
TMR1CS = 1:
1 = Do not synchronize external clock input
0 = Synchronize external clock input
TMR1CS = 0:
This bit is ignored. Timer1 uses the internal clock
TMR1CS: Timer1 Clock Source Select bit
1 = External clock from T1CKI pin (on the rising edge)
0 = Internal clock (F
TMR1ON: Timer1 On bit
1 = Enables Timer1
0 = Stops Timer1
TMR1GE
R/W-0
T1CON: TIMER 1 CONTROL REGISTER
(2)
W = Writable bit
‘1’ = Bit is set
T1CKPS1
R/W-0
OSC
/4)
T1CKPS0
(1)
R/W-0
(2)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
T1OSCEN
R/W-0
T1SYNC
R/W-0
© 2008 Microchip Technology Inc.
x = Bit is unknown
TMR1CS
R/W-0
TMR1ON
R/W-0
bit 0