EVAL-AD7731EBZ Analog Devices Inc, EVAL-AD7731EBZ Datasheet - Page 9
![BOARD EVALUATION FOR AD7731](/photos/9/11/91126/eval-ad7731eb_board_sml.jpg)
EVAL-AD7731EBZ
Manufacturer Part Number
EVAL-AD7731EBZ
Description
BOARD EVALUATION FOR AD7731
Manufacturer
Analog Devices Inc
Datasheets
1.AD7731BRUZ.pdf
(44 pages)
2.EVAL-AD7731EBZ.pdf
(11 pages)
3.EVAL-AD7731EBZ.pdf
(3 pages)
4.EVAL-AD7731EBZ.pdf
(44 pages)
Specifications of EVAL-AD7731EBZ
Number Of Adc's
1
Number Of Bits
24
Sampling Rate (per Second)
6.4k
Data Interface
Serial
Inputs Per Adc
3 Differential
Input Range
±1.28 V
Power (typ) @ Conditions
67.5mW @ 6.4kSPS
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
AD7731
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Pin
No.
20
21
22
23
24
REV. 0
TERMINOLOGY
INTEGRAL NONLINEARITY
This is the maximum deviation of any code from a straight line
passing through the endpoints of the transfer function. The end-
points of the transfer function are zero scale (not to be confused
with bipolar zero), a point 0.5 LSB below the first code transi-
tion (000 . . . 000 to 000 . . . 001) and full scale, a point 0.5 LSB
above the last code transition (111 . . . 110 to 111 . . . 111). The
error is expressed as a percentage of full scale.
POSITIVE FULL-SCALE ERROR
Positive Full-Scale Error is the deviation of the last code transi-
tion (111 . . . 110 to 111 . . . 111) from the ideal AIN(+) voltage
(AIN(–) + V
and bipolar analog input ranges.
UNIPOLAR OFFSET ERROR
Unipolar Offset Error is the deviation of the first code transition
from the ideal AIN(+) voltage (AIN(–) + 0.5 LSB) when oper-
ating in the unipolar mode.
BIPOLAR ZERO ERROR
This is the deviation of the midscale transition (0111 . . . 111
to 1000 . . . 000) from the ideal AIN(+) voltage (AIN(–) –
0.5 LSB) when operating in the bipolar mode.
GAIN ERROR
This is a measure of the span error of the ADC. It is a measure
of the difference between the measured and the ideal span be-
tween any two points in the transfer function. The two points
used to calculate the gain error are positive full scale and nega-
tive full scale.
BIPOLAR NEGATIVE FULL-SCALE ERROR
This is the deviation of the first code transition from the ideal
AIN(+) voltage (AIN(–) – V
ing in the bipolar mode. Negative full-scale error is a summation
of zero error and gain error.
Pin
Mnemonic
RDY
DOUT
DIN
DV
DGND
DD
REF
/GAIN – 3/2 LSBs). It applies to both unipolar
Function
Logic output. Used as a status output in both conversion mode and calibration mode. In conversion mode, a
logic low on this output indicates that a new output word is available from the AD7731 data register. The
RDY pin will return high upon completion of a read operation of a full output word. If no data read has
taken place after an output update, the RDY line will return high prior to the next output update, remain
high while the update is taking place and return low again. This gives an indication of when a read operation
should not be initiated to avoid initiating a read from the data register as it is being updated. In calibration
mode, RDY goes high when calibration is initiated and returns low to indicate that calibration is complete. A
number of different events on the AD7731 set the RDY high and these are outlined in Table XVII.
Serial Data Output with serial data being read from the output shift register on the part. This output shift
register can contain information from the calibration registers, mode register, status register, filter register or
data register depending on the register selection bits of the Communications Register.
Serial Data Input with serial data being written to the input shift register on the part. Data from this input
shift register is transferred to the calibration registers, mode register, communications register or filter regis-
ter depending on the register selection bits of the Communications Register.
Digital Supply Voltage, +3 V or +5 V nominal.
Ground reference point for digital circuitry.
REF
/GAIN + 0.5 LSB) when operat-
PIN FUNCTION DESCRIPTIONS (Continued)
–9–
POSITIVE FULL-SCALE OVERRANGE
Positive Full-Scale Overrange is the amount of overhead avail-
able to handle input voltages on AIN(+) input greater than
AIN(–) + V
ages due to system gain errors in system calibration routines)
without introducing errors due to overloading the analog modu-
lator or overflowing the digital filter.
NEGATIVE FULL-SCALE OVERRANGE
This is the amount of overhead available to handle voltages on
AIN(+) below AIN(–) – V
analog modulator or overflowing the digital filter.
OFFSET CALIBRATION RANGE
In the system calibration modes, the AD7731 calibrates its
offset with respect to the analog input. The Offset Calibration
Range specification defines the range of voltages the AD7731
can accept and still accurately calibrate offset.
FULL-SCALE CALIBRATION RANGE
This is the range of voltages that the AD7731 can accept in the
system calibration mode and still accurately calibrate full scale.
INPUT SPAN
In system calibration schemes, two voltages applied in sequence
to the AD7731’s analog input define the analog input range.
The input span specification defines the minimum and maxi-
mum input voltages from zero to full scale that the AD7731 can
accept and still accurately calibrate gain.
REF
/GAIN (for example, noise peaks or excess volt-
REF
/GAIN without overloading the
AD7731