ATDVK90CAN1 Atmel, ATDVK90CAN1 Datasheet - Page 41

• Manufacturer Part Number: ATDVK90CAN1
• Description: KIT DEV FOR AT90CAN128 MCU
• Manufacturer: Atmel

Specifications of ATDVK90CAN1

• Main Purpose: *
• Embedded: *
• Utilized Ic / Part: AT90CAN AVR Devices
• Primary Attributes: *
• Secondary Attributes: *
• Processor To Be Evaluated: AT90CAN
• Data Bus Width: 8 bit
• Interface Type: RS-232, SPI, TWI
• Core Architecture: AVR
• Core Sub-architecture: AVR UC3
• Kit Contents: Board, AT90CAN128 Sample Microcontroller, 9V Battery Power Cable, CD-ROM, Manuals
• Features: RS232, CAN, LIN, SPI & TWI Serial Interface
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

DVK90CAN1 Hardware User Guide
Table 3-18 . Configuration Pads
Reference
Config.
CP10
CP11
CP15
CP17
CP12
CP13
CP14
CP16
CP18
CP19
CP20
CP21
CP22
Pads
CP1
CP2
CP3
CP4
CP5
CP6
CP7
CP8
CP9
SleepLIN (PD7)
AUDIO-T (PB7)
LIGHT-S (PF1)
C-GND (GND)
VCCµC (VCC)
TEMP-S (PF0)
VOLT-S (PF2)
RxCAN (PD6)
TxCAN (PD5)
AVCC (VCC)
RxLIN (PD2)
LED-0 (PA0)
LED-1 (PA1)
LED-2 (PA2)
LED-3 (PA3)
LED-4 (PA4)
LED-5 (PA5)
LED-6 (PA6)
LED-7 (PA7)
TxLIN (PD3)
NRESET
(RESET)
Related
Signals
AVCC
These configuration pads are used to disconnect/connect
the CAN transceiver from AT90CAN128.
This configuration pad is used to disconnect/connect the
CAN Ground (C-GND) from DVK90CAN1 Ground (GND).
These configuration pads are used to disconnect/connect
the LIN transceiver from AT90CAN128.
This configuration pad is used to disconnect/connect the
AT90CAN128 VCC (VCCµC) from DVK90CAN1 power
supply (VCC). It is useful to measure the AT90CAN128
consumption.
This configuration pad is used to disconnect/connect the
ferrite bar when AVCC is supplied to AT90CAN128 by VCC.
This configuration pad is used to disconnect/connect the
AT90CAN128 AVCC from DVK90CAN1 AVCC. It is useful to
measure the analog AT90CAN128 consumption.
This configuration pad is used to disconnect/connect the
piezo audio transducer from AT90CAN128.
This configuration pad is used to disconnect/connect the
temperature sensor from AT90CAN128, analog connector.
This configuration pad is used to disconnect/connect the
luminosity sensor from AT90CAN128.
This configuration pad is used to disconnect/connect the
voltage reading from AT90CAN128.
These configuration pads are used to disconnect/connect
the 8-LED group from AT90CAN128.
This configuration pad is used to disconnect the NRESET
from application and re-connect the RESET pin of
AT90CAN128 to +12Volts in case of parallel programming
(EXP. CON 0 pin15 if STK500 used).
Function
Using the DVK90CAN1
4381A–AVR–Sept 04
page 39