AFCT-5961ATGZ Avago Technologies US Inc., AFCT-5961ATGZ Datasheet - Page 6

• Manufacturer Part Number: AFCT-5961ATGZ
• Description: TXRX OPT SM SONET OC3/SDH 2X5
• Manufacturer: Avago Technologies US Inc.
• Series: METRAKr

Specifications of AFCT-5961ATGZ

• Applications: General Purpose
• Data Rate: 155Mbps
• Wavelength: 1300nm
• Voltage - Supply: 3.1 V ~ 3.5 V
• Connector Type: LC Duplex
• Mounting Type: Through Hole
• Data Rate Max: 0.155Gbps
• Supply Voltage: 3.3V
• Wavelength Typ: 1300nm
• Leaded Process Compatible: Yes
• Optical Fiber Type: TX/RX
• Data Transfer Rate: 155Mbps
• Optical Rise Time: 2/2.2ns
• Optical Fall Time: 2/2.2ns
• Operating Temperature Classification: Industrial
• Peak Wavelength: 1360nm
• Package Type: DIP With Connector
• Operating Supply Voltage (min): 3.1V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.5V
• Output Current: 50mA
• Operating Temp Range: -40C to 85C
• Mounting: Snap Fit To Panel
• Pin Count: 10
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Connection Diagram
Figure 5. Pin Out Diagram (Top View)
Pin Descriptions:
Pin 1 Receiver Signal Ground V
Directly connect this pin to the receiver ground plane.
Pin 2 Receiver Power Supply V
Provide +3.3 V dc via the recommended receiver
power supply filter circuit. Locate the power supply
filter circuit as close as possible to the V
the filter circuit should not cause V
minimum specification.
Pin 3 Signal Detect SD:
Normal optical input levels to the receiver result in a
logic “1” output.
Low optical input levels to the receiver result in a logic
“0” output.
This Signal Detect output can be used to drive a LVPECL
input on an upstream circuit, such as Signal Detect
input or Loss of Signal-bar.
Pin 4 Receiver Data Out Bar RD-:
No internal terminations are provided. See recommend-
ed circuit schematic.
Pin 5 Receiver Data Out RD+:
No internal terminations are provided. See recommend-
ed circuit schematic.
6
RECEIVER SIGNAL GROUND
RECEIVER POWER SUPPLY
RECEIVER DATA OUT BAR
RECEIVER DATA OUT
SIGNAL DETECT
o
o
o
o
o
CC
RX
EE
1
2
3
4
5
RX:
RX:
View
Top
10
TX
9
8
7
6
o
o
o
o
o
CC
CC
to drop below
TRANSMITTER DATA IN BAR
TRANSMITTER DATA IN
TRANSMITTER DISABLE
TRANSMITTER SIGNAL GROUND
TRANSMITTER POWER SUPPLY
RX pin. Note:
Mounting Studs/
Solder Posts
Pin 6 Transmitter Power Supply
V
Provide +3.3 V dc via the recommended transmitter
power supply filter circuit. Locate the power supply
filter circuit as close as possible to the V
Pin 7 Transmitter Signal Ground
V
Directly connect these pins to the transmitter signal
ground plane.
Pin 8 Transmitter Disable T
Optional feature, connect this pin to +3.3 V TTL logic
high “1” to disable module. To enable module connect
to TTL logic low “0”.
Pin 9 Transmitter Data In TD+:
No internal terminations are provided. See recommend-
ed circuit schematic.
Pin 10 Transmitter Data In Bar TD-:
No internal terminations are provided. See recommend-
ed circuit schematic.
Mounting Studs/Solder Posts
The two mounting studs are provided for transceiv-
er mechanical attachment to the circuit board. It is
recommended that the holes in the circuit board be
connected to chassis ground.
CC
EE
TX:
TX:
DIS
:
CC
TX pin.