AFCT-5710PZ Avago Technologies US Inc., AFCT-5710PZ Datasheet
AFCT-5710PZ
Specifications of AFCT-5710PZ
Available stocks
Related parts for AFCT-5710PZ
AFCT-5710PZ Summary of contents
Page 1
... DMI is not needed. Throughout this datasheet, AFCT-571 Z will refer to the entire product family encompassing this full range of product options. Part Number Options The AFCT-571 Z SFP family consists of the following products: Part Number DMI Temperature AFCT-5710LZ No Extended AFCT-5710PZ No Extended AFCT-5710ALZ No Industrial AFCT-5710APZ No Industrial AFCT-5715LZ Yes Extended ...
Page 2
... Voltage Differential type coupled and terminated internally to the module. The internal termination is a 100 Ohm differential load. Installation The AFCT-571 Z can be installed in or removed from any MSA-compliant Pluggable Small Form Factor (SFP) port regardless of whether the host equipment is operating or not. The module is simply inserted, elec- trical-interface fi ...
Page 3
ENGAGEMENT SEQUENCE TD– RD+ 12 RD– TOP OF ...
Page 4
... TX_FAULT output will be activated. Receiver Section The receiver section for the AFCT-571 Z contains an InGaAs/InP photo detector and a preamplifier mounted in an optical subassembly. This optical subassembly is coupled to a post amplifier/decision circuit on a circuit board ...
Page 5
... Application Support An Evaluation Kit and Reference Designs are available to assist in evaluation of the AFCT-571 Z SFPs. Please contact your local Field Sales representative for avail- ability and ordering details. Table 1. Regulatory Compliance ...
Page 6
... See Table 1. Flammability The AFCT-571 Z family of SFPs is compliant to UL 94V-0. Customer Manufacturing Processes This module is pluggable and is not designed for aqueous wash, IR reflow, or wave soldering processes. ...
Page 7
Table 2. Pin description Pin Name Function/Description 1 VeeT Transmitter Ground 2 TX Fault Transmitter Fault Indication 3 TX Disable Transmitter Disable - Module disables on high or open 4 MOD-DEF2 Module Definition 2 - Two wire serial ID interface ...
Page 8
... Control Input Voltage Table 4. Recommended Operating Conditions Typical operating conditions are those values for which functional performance and device reliability is implied. Parameter Case Operating Temperature AFCT-5710LZ/PZ & AFCT-5715LZ/PZ AFCT-5710ALZ/APZ & AFCT-5715ALZ/APZ Supply Voltage Table 5. Transceiver Electrical Characteristics Parameter Module supply current Power Dissipation ...
Page 9
Table 6. Transmitter Optical Characteristics Parameter Average Optical Output Power Optical Extinction Ratio TX Optical Eye Mask Margin Center Wavelength Spectral Width - rms Optical Rise/Fall Time Relative Intensity Noise Contributed Total Jitter (Transmitter) 1.25 Gb/s POUT TX_DISABLE Asserted Notes: ...
Page 10
Table 8. Transceiver Timing Characteristics Parameter Hardware TX_DISABLE Assert Time Hardware TX_DISABLE Negate Time Time to initialize, including reset of TX_FAULT Hardware TX_FAULT Assert Time Hardware TX_DISABLE to Reset Hardware RX_LOS Assert Time Hardware RX_LOS De-Assert Time Software TX_DISABLE Assert ...
Page 11
V > 2. Tx_FAULT Tx_DISABLE TRANSMITTED SIGNAL t_init t-init: TX DISABLE NEGATED V > 2. Tx_FAULT Tx_DISABLE TRANSMITTED SIGNAL t_init INSERTION t-init: TX DISABLE NEGATED, MODULE HOT PLUGGED OCCURANCE OF FAULT Tx_FAULT Tx_DISABLE TRANSMITTED SIGNAL t_fault ...
Page 12
Table 10. EEPROM Serial ID Memory Contents - Page A0h Byte # Data Decimal Hex Notes 0 03 SFP physical device 1 04 SFP function defined by serial ID only optical connector ...
Page 13
... Table 11. Part Number Extensions and Datafields AFCT-5710ALZ Address Hex ASCII Address AFCT-5715ALZ Address Hex ASCII Address AFCT-5710APZ AFCT-5710LZ Hex ASCII Address Hex AFCT-5715APZ AFCT-5715LZ Hex ASCII Address Hex AFCT-5710PZ ASCII Address Hex AFCT-5715PZ ASCII Address Hex ASCII ASCII ...
Page 14
... Transmitted average optical power (Tx Pwr) is decoded bit unsigned integer in increments of 0.1 μW. 5. Received average optical power (Rx Pwr) is decoded bit unsigned integer in increments of 0.1 μW. 6. Bytes 55-94 are not intended from use with AFCT-5715xxxx, but have been set to default values per SFF-8472. 7. Bytes checksum calculated (per SFF-8472) and stored prior to product shipment. ...
Page 15
... Bit 6 is logic OR’d with the SFP Tx_Disable input pin 3 ... either asserted will disable the SFP transmitter. 2. AFCT-5715Z does not respond to state changes on Rate Select Input Pin internally hardwired to full bandwidth. Table 14. EEPROM Serial ID Memory Contents - Address A2h, Bytes 112, 113, 116, 117 ...
Page 16
... PROCESS PLUG 6.6 [0.261] 13.50 [0.53] 14.8 MAX. UNCOMPRESSED [0.583] 12.1±0.2 DIMENSIONS ARE IN MILLIMETERS (INCHES) [0.48±0.01] AFCT-571xZ 1300 nm LASER PROD 21CFR(J) CLASS 1 COUNTRY OF ORIGIN YYWW XXXXXX 13.4±0.1 [0.528±0.004] 55.2±0.2 [2.17±0.01] 0.7MAX. UNCOMPRESSED [0.028] 8.5±0.1 ...
Page 17
X Y 10x 1.05 ± 0.01 16.25 MIN. PITCH B PCB EDGE 5.68 8.58 11.08 16.25 REF. 14.25 2.0 11x 3 5 3.2 0.9 20 PIN 1 10.93 9.6 0.8 TYP 1.55 ± 0.05 0.1 L ...
Page 18
PCB [1.64±.02] 15MAX [.59] CAGE ASSEMBLY 12.4REF [.49] 9.8MAX [.39] Figure 8. Assembly Drawing 18 1.7±0.9 [.07±.04] AREA FOR BEZEL PROCESS PLUG Tcase REFERENCE POINT 10REF 1.15REF [.39] [.05] TO PCB BELOW PCB 0.4±0.1 [.02±0.004] BELOW PCB ...
Page 19
... DMI AFCT-5715ALZ DMI AFCT-5715APZ DMI AFCT-5710LZ No DMI AFCT-5710PZ No DMI AFCT-5710ALZ No DMI AFCT-5710APZ No DMI For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. ...