AFBR-57R5APZ Avago Technologies US Inc., AFBR-57R5APZ Datasheet - Page 4

• Manufacturer Part Number: AFBR-57R5APZ
• Description: TXRX OPT SFP 4/2/1GBD 850NM
• Manufacturer: Avago Technologies US Inc.

Specifications of AFBR-57R5APZ

• Data Rate: 4.25GBd
• Wavelength: 850nm
• Voltage - Supply: 3.3V
• Connector Type: LC Duplex
• Mounting Type: SFP
• Function: Digital Diagnostic SFP, supports high-speed serial links over multimode optical fiber.
• Product: Transceiver
• Maximum Rise Time: 0.09 ns/0.15 ns
• Maximum Fall Time: 0.09 ns/0.15 ns
• Pulse Width Distortion: 0.06 ns (Max)/0.062 ns (Max)
• Operating Supply Voltage: 2.97 V to 3.63 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 10 C
• Package / Case: SFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Applications: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With: Multimode Glass
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1987

4
Receiver Loss of Signal (Rx_LOS)
The post-amplification IC also includes transition
detection circuitry which monitors the ac level of
incoming optical signals and provides a TTL/CMOS
compatible status signal to the host (pin 8). An adequate
optical input results in a low Rx_LOS output while a high
Rx_LOS output indicates an unusable optical input. The
Rx_LOS thresholds are factory set so that a high output
indicates a definite optical fault has occurred. Rx_LOS
can also be monitored via the two-wire serial interface
(address A2h, byte 110, bit 1).
Functional Data I/O
The AFBR-57R5APZ interfaces with the host circuit board
through twenty I/O pins (SFP electrical connector) iden-
tified by function in Table 2. The board layout for this
interface is depicted in Figure 6.
The AFBR-57R5APZ high speed transmit and receive
interfaces require SFP MSA compliant signal lines on
the host board. To simplify board requirements, biasing
resistors and ac coupling capacitors are incorporated into
the SFP transceiver module (per SFF-8074i) and hence are
not required on the host board. The Tx_Disable, Tx_Fault,
and Rx_LOS lines require TTL lines on the host board (per
SFF-8074i) if used. If an application chooses not to take
advantage of the functionality of these pins, care must be
taken to ground Tx_Disable (for normal operation).
Figure 2 depicts the recommended interface circuit to
link the AFBR-57R5APZ to supporting physical layer ICs.
Timing for MSA compliant control signals implemented
in the transceiver are listed in Figure 4.
Application Support
An Evaluation Kit and Reference Designs are available to
assist in evaluation of the AFBR-57R5APZ. Please contact
your local Field Sales representative for availability and
ordering details.
Ordering Information
Please contact your local field sales engineer or one of
Avago Technologies franchised distributors for ordering
information. For technical information, please visit Avago
Technologies’ WEB page at www.avagotech.com or contact
Avago Technologies Semiconductor Products Customer
Response Center at 1-800-235-0312. For information
related to SFF Committee documentation visit www.
sffcommittee.org.
Caution
There are no user serviceable parts nor maintenance
requirements for the AFBR-57R5APZ. All mechanical
adjustments are made at the factory prior to shipment.
Tampering with, modifying, misusing or improp-
erly handling the AFBR-57R5APZ will void the product
warranty. It may also result in improper operation
and possibly overstress the laser source. Performance
degradation or device failure may result. Connection of
the AFBR-57R5APZ to a light source not compliant with
ANSI FC-PI or IEEE 802.3 specifications, operating above
maximum operating conditions or in a manner inconsis-
tent with it’s design and function may result in exposure
to hazardous light radiation and may constitute an act
of modifying or manufacturing a laser product. Persons
performing such an act are required by law to re-certify
and re-identify the laser product under the provisions of
U.S. 21 CFR (Subchapter J) and TUV.
Regulatory Compliance
The AFBR-57R5APZ complies with all applicable laws
and regulations as detailed in Table 1. Certification level
is dependent on the overall configuration of the host
equipment. The transceiver performance is offered as a
figure of merit to assist the designer.
Electrostatic Discharge (ESD)
The AFBR-57R5APZ is compatible with ESD levels found
in typical manufacturing and operating environments
as described in Table 1. In the normal handling and
operation of optical transceivers, ESD is of concern in two
circumstances.
The first case is during handling of the transceiver prior
to insertion into an SFP compliant cage. To protect the
device, it’s important to use normal ESD handling pre-
cautions. These include use of grounded wrist straps,
work-benches and floor wherever a transceiver is
handled.
The second case to consider is static discharges to the
exterior of the host equipment chassis after installation.
If the optical interface is exposed to the exterior of host
equipment cabinet, the transceiver may be subject to
system level ESD requirements.