HFBR-2536 Avago Technologies US Inc., HFBR-2536 Datasheet
![RCVR OPT HI SPEED VERS LINK VERT](/photos/26/68/266869/5989-4631_sml.jpg)
HFBR-2536
Specifications of HFBR-2536
Related parts for HFBR-2536
HFBR-2536 Summary of contents
Page 1
... The 125 MBd Versatile Link (HFBR-0507Z Series) is the most cost-effective fiber-optic solution for transmission of 125 MBd data over 100 meters. The data link consists of a 650 nm LED transmitter, HFBR-15X7Z, and a PIN/pre- amp receiver, HFBR-25X6Z. These can be used with low- cost plastic or silica fiber. One mm diameter plastic fiber provides the lowest cost solution for distances under 25 meters ...
Page 2
... Typical performance is at 25°C, 125 MBd, and is measured with typical values of all circuit components. 5. Standard cable is HFBR-RXXYYYZ plastic optical fiber , with a maximum attenuation of 0.24 dB/m at 650 nm and NA = 0.5. Extra low loss cable is HFBR-EXXYYYZ plastic optical fiber, with a maximum attenuation of 0.19 dB/m at 650 nm and NA = 0.5. ...
Page 3
... Average Modulated Power = 3. High and low level LED currents refer to the current through the HFBR-15X7Z LED. The low level LED “off” current, sometimes referred to as “hold-on” current, is prebias supplied to the LED during the off state to facilitate fast switching speeds. ...
Page 4
... Modulated Optical Power 200 µm HCS Receiver Application Circuit Current Consumption Notes: 4. Performance in response to a signal from the HFBR-15X7Z transmitter driven with the recommended circuit at 1-125 MBd over 1 meter of HFBR-RZ/EXXYYYZ plastic optical fiber or 1 meter of HFBR-H/VXXYYY hard clad silica optical fiber. 5. Terminated through a 50 Ω resistor ...
Page 5
V ECL SERIAL DATA SOURCE 0.1 µ Ð µF 0.1 µF 10 µF 0.1 µ ECL SERIAL DATA RECEIVER 120 120 Figure 2. Recommended power supply filter and +5 ...
Page 6
... LED in a horizontal (HFBR-1527Z) or vertical (HFBR-1537Z) gray housing. The HFBR-15X7Z transmit- ters are suitable for use with current peaking to decrease response time and can be used with HFBR-25X6Z receiv- ers in data links operating at signal rates from 1 to 125 megabaud over 1 mm diameter plastic optical fiber or 200 µ ...
Page 7
... Optical Power measured at the end of 0.5 meter diameter plastic or 200 µm diameter hard clad silica optical fiber with a large area detector. 4. Typical value measured from junction to PC board solder joint for horizontal mount package, HFBR-1527Z. θ 30°C/W higher for vertical mount package, HFBR-1537Z. ...
Page 8
HP8082A PULSE BCP MODEL 300 GENERATOR 500 MHz BANDWIDTH SILICON AVALANCHE PHOTODIODE HP54002A 50 OHM 50 OHM BNC LOAD OSCILLOSCOPE INPUT POD RESISTOR Figure 1. Test circuit for measuring unpeaked rise and fall times. 2.4 ° 2.2 ° ...
Page 9
... Description The HFBR-25X6Z receivers contain a PIN photodiode and transimpedance pre-amplifier circuit in a horizontal (HFBR-2526Z) or vertical (HFBR-2536Z) blue housing, and are designed to interface to 1mm diameter plastic opti- cal fiber or 200 µm hard clad silica glass optical fiber. The receivers convert a received optical signal to an analog output voltage ...
Page 10
Electrical/Optical Characteristics 0 to 70°C; 5.25 V ≥ V Parameter AC Responsivity 1 mm POF AC Responsivity 200 µm HCS RMS Output Noise Equivalent Optical Noise Input Power, RMS - 1 mm POF Equivalent Optical Noise Input Power, RMS - ...
Page 11
Figure 1. Recommended power supply filter circuit. Figure 2. Simplified receiver schematic. Figure 3. Typical pulse width distortion vs. peak input power. 11 Figure 4. Typical output spectral noise density vs. frequency. Figure 5. Typical rise and fall time vs. ...
Page 12
... Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2008 Avago Technologies. All rights reserved. Obsoletes 5989-4631EN AV02-1502EN - October 20, 2008 HORIZONTAL MODULES HFBR-1537Z HFBR-2526Z 2.03 (0.080) 10.16 (0.400) 5.08 (0 ...