4165100-XX Digital View Inc, 4165100-XX Datasheet - Page 13

• Manufacturer Part Number: 4165100-XX
• Description: CTRLR SVP-1280 VGA-SXGA PNLS
• Manufacturer: Digital View Inc

Specifications of 4165100-XX

• Voltage - Input: 12V
• Voltage - Output: 3.3V, 5V, 12V
• Size / Dimension: 7" L x 4.74" W (179mm x 120.4mm)
• Power (watts): 10W
• Operating Temperature: 0°C ~ 60°C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 586-1004

Summary: Jumpers setting
SW1: Panel and function selection
JP13~15
Pos. #1
JB10
JP20
JP21
JP26
SW1
Pos. #3
Pos. #4
OFF
OFF
JA1
JA2
JA3
JA5
JA7
JB2
JB3
Ref
JT1
JT2
JT3
JT4
JT5
JT6
ON
ON
On board +5V logic power enable
On board +3.3V logic power enable
:
:
Panel power voltage select
CAUTION: Incorrect setting can damage panel
+12V panel power
+12V power source on connector CNA1
Backlight inverter on/off control – signal level
CAUTION: Incorrect setting can damage
inverter.
Backlight inverter on/off control – polarity
Backlight power enable
Panel clock select
Reserved
Reserved
Reserved
Composite video-in terminator enable
S-Video luma-in terminator enable
S-Video chroma-in terminator enable
Component luma-in terminator enable
Component Cr-in terminator enable
Component Cb-in terminator enable
Panel & function selection
Pos. #2
OFF
OFF
ON
ON
Panel type selection. Please refer to the connection diagram for proper setting.
Clock Phase selection (Use this setting to stabilize the screen display. Please refer to connection diagram
for proper setting).
Purpose
Description
13
SVGA
SXGA
VGA
XGA
1-2 & 3-4 closed, factory set, do not remove
1-2 & 3-4 closed, factory set, do not remove
1-3 & 2-4 = DC12V available on pin 1 of CNA1
1-3 & 2-4 = +5V panel voltage (Factory set)
3-5 & 4-6 = +3.3V panel voltage
Close = +12V panel power available on CN3
Open = +12V panel power not available on CN3
3-5 & 4-6 = backlight 12V (controlled by JB10) available on pin
1 of CNA1
** CNA1 provides additional +12V power pin for high current
backlight driver board.
1-2 = On/Off control signal ‘High’ = +12V
2-3 = On/Off control signal ‘High’ = +5V
Open = On/Off control signal ‘High’ = Open collector
1-2 = control signal ‘high’ = CCFT ON
2-3 = control signal ‘low’ = CCFT ON
Open = backlight +12V power supply is always enabled
Close = backlight +12V power supply is switched off when
backlight is off.
JP13: 1-2 & JP14: 2-3 & JP15: open = 101.6MHz (for SXGA)
JP13: 1-2 & JP14: 2-3 & JP15: 2-3 = 65MHz (for XGA)
JP13: 3-4 & JP14: 1-2 & JP15: 2-3 = 40.6MHz (for SVGA)
JP13: 3-4 & JP14: 1-2 & JP15: open = 25.4MHz (for VGA)
Factory set to 1-2
Factory set to open
Factory set to open
Open = composite video input is not terminated
Close = composite video input is terminated with 75Ω
Open = S-video luma input is not terminated
Close = S-video luma input is terminated with 75Ω
Open = S-video chroma input is not terminated
Close = S-video chroma input is terminated with 75Ω
Open = component luma input is not terminated
Close = component luma input is terminated with 75Ω
Open = component Cr input is not terminated
Close = component Cr input is terminated with 75Ω
Open = component Cb input is not terminated
Close = component Cb input is terminated with 75Ω
See table below
Note