M0120SD-201MDBR1-1 Newhaven Display, M0120SD-201MDBR1-1 Datasheet
M0120SD-201MDBR1-1
Specifications of M0120SD-201MDBR1-1
Related parts for M0120SD-201MDBR1-1
M0120SD-201MDBR1-1 Summary of contents
Page 1
... M0120SD‐201MDB1‐1 Vacuum Fluorescent Display Module RoHS Compliant ...
Page 2
...
Page 3
...
Page 4
Power-on Reset and /or RESET Signal Timing T off(Vcc 100ms 0.2V Fig-1 Power-on Reset and RESET signal Timing 4.8.2 i80 type CPU bus write in Timing RS T str(RS) Min 10ns /WR DB0-DB7 Fig –2 Data write-in ...
Page 5
M68 type CPU bus write in timing Fig-4 Data write-in Timing Diagram(M68 bus interface) 4.8.5 M68 type CPU bus read-out Timing R/W T sh(rs,r/ 20ns cyc M ax 160ns DB0-DB7 Fig-5 Data read-out Timing ...
Page 6
Fig-7 Outer dimensions ...
Page 7
...
Page 8
Table-8 Register Selection M68 i80 RS R/W /RD / 5.1.1 Busy Flag (BF) When the busy flag is 1, the controller is in the ...
Page 9
Table-10 Characters Font Table (CG-ROM)and CG-RAM codes 0 CG-RAM (1) 1 CG-RAM (2) CG-RAM (3) CG-RAM (4) CG-RAM ...
Page 10
Table-11 Relationship between CG-RAM address, Character Codes (DD-RAM) AND 5*7 Dot Character Patterns (CG-RAM) Character Codes (DD-RAM DATA ...
Page 11
MPUs. For 4-bit interface data, only four bus lines (DB4 to DB7) are used for transfer. When to use 4-bit parallel data transfer, DB0 to DB3 keep “H”or “L”. The data transfer between the ...
Page 12
Display on/o control: D=0; Display o B=0; Blinking o C=0; Cursor o 4) Entry mode set: L/D=1; Increment by 1 S=0; No shift 5) Function set IF=1; 8-bit interface data BR0=BR1=0; Brightness=100% N=1; 2-line display 6) CPU interface type ...
Page 13
Outline Only the instruction register (IR) and data register (DR) of the VFD controller can be controlled by the user's MPU. Before starting the internal operation of the controller, control information is temporarily stored into these registers to allow ...
Page 14
Table –13 Instruction Set Instruction RS R/W Display clear 0 0 Cursor Home 0 0 Entry Mode set 0 0 Display ON/OFF 0 0 Control Cursor or display 0 0 Shift Function set 0 0 CGRAM address 0 0 Setting ...
Page 15
Data write DDRAM Data Read from DDRAM I/D=1: Increment I/D=0: Decrement S=1: Display shift enabled S=0: Cursor shift enabled S/C=1: Display shift S/C=0: Cursor move R/L=1: Shift to the right R/L=0: ...
Page 16
Cursor Home DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 RS=0, R/W=0 This instruction (1) Clears the contents of the address counter (ACC) to 00H. (2) Sets the address counter (ACC) to point to the ...
Page 17
Display ON/OFF DB7 DB6 DB5 DB4 RS=0, R/W=0 This instruction controls various features of the display. D=1: Display on , D=0: Display off. C=1: Cursor on C=0: Cursor off. B=1: Blinking on B=0: blinking off. ...
Page 18
Set DB7 DB6 DB5 DB4 RS=0, R/W=0 This instruction sets width of data bus line.(when to use parallel interface. IM=1). The number of display line and brightness control. This instruction initializes the system, and must ...
Page 19
This instruction (1) Loads a new 7-bit address into the address counter (ACC). (2) Sets the address counter (ACC) to point to the DD-RAM. Once the “Set DD-RAM Address” instruction has been executed, the contents of the address counter (ACC) ...
Page 20
... Since all VFD modules contain C-MOS ICs, anti-static handing procedures are always required. NOTE: Newhaven Display reserves the right to change or modify this spec and or design without notice in order to improve the design or ensure the quality of this product. ...