LQ035Q7DH01 Sharp Microelectronics, LQ035Q7DH01 Datasheet
LQ035Q7DH01
Specifications of LQ035Q7DH01
Available stocks
Related parts for LQ035Q7DH01
LQ035Q7DH01 Summary of contents
Page 1
... P S RODUCT PECIFICATIONS LQ035Q7DH01 TFT-LCD Module Spec. Issue Date: Oct. 21, 2003 No: LCP-03015A Mobile Liquid Crystal Displays Group ...
Page 2
...
Page 3
RECORDS OF REVISION ＭＯＤＥＬ Ｎｏ：ＬＱ０３５Ｑ７ＤＨ０１ ＳＰＥＣ Ｎｏ ：ＬＣＰ−０３０１５ NO. 2003.06 .13 ＬＣＰ−０３０１５ 2003.10 .21 ＬＣＰ−０３０１５Ａ PAGE SUMMARY - - 5 Touch panel driving section 8 Setup time of Vcom : Min Value 21 Outline Dimensions NOTE 1 st Issue Correction ...
Page 4
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any ...
Page 5
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any ...
Page 6
... Application This specification applies to LQ035Q7DH01 (2) Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor), named AD-TFT(Advanced TFT practicable in both transmissive-type and reflection- type modes composed of a color TFT-LCD panel, driver ICs, an FPC, a back light, a touch panel and a back sealed casing. It isn’ ...
Page 7
Table2 Pin No. Symbol I/O VL1 I Power supply for LED (High voltage − 2 VL2 I Power supply for LED (Low voltage VEE Power supply of gate driver(low level) ...
Page 8
Pin No. Symbol I/O 40 DGND Ground(digital) − RED data signal(MSB RED data signal RED data signal RED data signal RED data signal 46 R0 ...
Page 9
Table 4 Pin No. Symbol I − − − − (6)Absolute Maximum Ratings Parameter Symbol Power supply(source/Analog) Power supply(source/Digital) Power supply (gate) Power supply (gate) Input voltage (Digital) ...
Page 10
A) TFT-LCD panel driving section Table 6 Parameter Supply voltage for source driver (Analog) Supply voltage for source driver (Digital) Supply voltage High voltage for gate driver Low voltage Input voltage for Source driver (Low) ...
Page 11
B0∼B5 terminals are applied. 【Note 7-2】DCLK,SPL,SPR,LBR,LP,REV,R0∼R5,G0∼G5 and B0∼B5 terminals are applied. 【Note 7-3】PS terminal is applied. 【Note 7-4】MOD,CLS,SPS and U/L terminals are applied. 【Note 7-5】VCOMAC should be alternated on VCOMDC every 1 horizontal period and 1 vertical ...
Page 12
...
Page 13
...
Page 14
Timing Characteristics of input signals Table 8 AC Characteristics (1) Parameter Clock frequency of source driver Rising time of clock Falling time of clock Pulse width (High level) Pulse width (Low level) Frequency of start pulse Setup time of ...
Page 15
Measurement condition : SPS=60Hz,CLS=15.73kHz,SPL=15.73kHz,DCLK=6.3MHz The term of PS=”Lo” in one horizontal period … 37μsec(234DCLK) Ta=25℃ Table 9 Parameter Sym Source Analog ISHA VSHA=+5.0V current Digital ISHD VSHD=+3.3V Gate High IDD current Low IEE 【Note 7-8】Vertical stripe pattern alternating ...
Page 16
Signals, Basic Display Color and Gray Scale of Each Color Table 10 Colors & Gray scale Gray Scale Black 0 0 − Blue 0 0 − Green 0 0 − Cyan 0 0 − Red 1 ...
Page 17
Back light condition Table 11 Parameter Symbol θ21,22 Viewing angle θ11 range θ12 Contrast ratio CRmax τ r Response Rise τ d time Fall White chromaticity x y Reflection ratio R * The measuring method ...
Page 18
Back light condition Table 12 Parameter Symbol θ21,22 Viewing angle θ11 range θ12 Contrast ratio Crmax τ r Response Rise τ d time Fall White chromaticity x y Brightness Y LED life time LL * The measuring method ...
Page 19
Viewing angle range is defined as follows. θ 22 θ 11 ６o’clock direction Definition for viewing angle [Note 9-2] Definition of contrast ratio: The contrast ratio is defined as follows: Photodetecter output with all pixels white(GS63) Contrast ratio(CR)= ...
Page 20
A measurement device is Minolta CM-2002. [Note 9-5] Definition of reflection ratio Reflection ratio = [Note 9-6] A measurement device is ELDIM EZContrast [Note 9-7] This is the reference value. The White-LED life time is defind as a ...
Page 21
T/P should be supported from the backside of the Plastic. (2)Do not to use an adhensive-tape to bond it on the front of T/P and hang it to the housing ...
Page 22
Precautions 13-1) Insertion and taking out of FPCs Be sure insert and take out of the FPC into the connector of the set after turning off the power supply on the set side. 13-2) Handling of FPCs The FPC ...
Page 23
Test Conditions for TFT-LCD Module No. Test items High temperature storage test Ta=+70℃ Low temperature storage test 3 High temperature and high humidity operating test 4 High temperature test Low temperature operating test Tp=-10℃ Electro ...
Page 24
... The lot number is shown on a label. Attached location is shown in Fig.1 (Outline Dimensions). Indicated contents of the label LQ035Q7DH01 ○○○○○○○○ model No. 15-2) Used Regulation of Chemical Substances Breaking Ozone Stratum Substances with the object of regulating : CFCS, Carbon tetrachloride, Halon (a) This LCD module, Constructed part and Parts don’ ...
Page 25
LCP-03015−21 ...
Page 26
Fig.3 Forwarding Form LCP-03015-22 Model No. Date Quantity Revision code Ｍｏｄｅｌ Ｎｏ． Ｑｕａｎｔｉｔｙ ...
Page 27
... ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED event will SHARP be liable any way responsible, for any incidental or consequential economic or property damage. NORTH AMERICA SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 ...